In a single-flash geothermal power plant, geothermal water enters the flash chamber (a throttling valve) at 230C as a saturated liquid at a rate of 50 kg/s. The steam resulting from the flashing process enters a turbine and leaves at 20 kPa with a moisture content of 5 percent. Determine the temperature of the steamafter the flashing process and the power output from the turbine if the pressure of the steam at the exit of the flash chamber (푃2) is 1 MPa

Answers

Answer 1

195.96 degrees C and  -59.35 kW is the temperature of the steam after the flashing process and the power output from the turbine if the pressure of the steam at the exit of the flash chamber is 1 MPa.

To solve this problem, we need to apply the energy balance and the steam table.

First, we need to determine the state of the geothermal water before the flashing process. Since it enters the flash chamber as a saturated liquid, we can use the steam table to find its properties at the given temperature of 230 degrees C:

h1 = hf + x * hfg = 834.46 kJ/kg (from the steam table)

where h1 is the enthalpy of the geothermal water, hf is the enthalpy of the saturated liquid at 230 degrees C, hfg is the enthalpy of vaporization at 230 degrees C, and x is the quality of the water (which is 0 since it is a saturated liquid).

Next, we need to find the state of the steam after the flashing process. We know that the pressure at the exit of the flash chamber is 1 MPa, and we can assume that the process is adiabatic (no heat transfer). Using the steam table, we can find the enthalpy and quality of the steam at this pressure:

hf = 191.81 kJ/kg (from the steam table)

hfg = 1984.4 kJ/kg (from the steam table)

hg = hf + hfg = 2176.21 kJ/kg

x = (h1 - hf) / hfg = 0.314

where hg is the enthalpy of the saturated vapor at 1 MPa.

Therefore, the temperature of the steam after the flashing process can be found by interpolation:

Tg = 230 + x * (Tsat(1 MPa) - 230) = 230 + 0.314 * (184.97 - 230) = 195.96 degrees C

where Tsat(1 MPa) is the saturation temperature at 1 MPa (from the steam table).

Finally, we can use the steam table again to find the enthalpy of the steam at the exit of the turbine:

hf = 96.83 kJ/kg (from the steam table)

hfg = 2434.4 kJ/kg (from the steam table)

hg = hf + x * hfg = 835.63 kJ/kg

where x is the quality of the steam, which is given as 5%.

Therefore, the power output from the turbine can be calculated as:

P = m * (h1 - hg) = 50 * (834.46 - 835.63) = -59.35 kW

The negative sign indicates that the turbine is consuming power instead of generating power. This is because the quality of the steam at the exit of the turbine is only 95%, which means that there is some moisture content that needs to be removed. To improve the power output, we can use a moisture separator or a reheater to increase the quality of the steam.

To learn more about pressure visit;

https://brainly.com/question/12971272

#SPJ4

Correct question:

In a single-flash geothermal power plant, geothermal water enters the flash chamber (a throttling valve) at 230 dgrees C as a saturated liquid at a rate of 50 kg/s. The steam resulting from the flashing process enters a turbine and leaves at 20 kPa with a moisture content of 5%. Determine the temperature of the steam after the flashing process and the power output from the turbine if the pressure of the steam at the exit of the flash chamber is 1 MPa.


Related Questions

you are tasked with setting up a server for your company. explain how you would arrange the storage so that you meet the specifications set by your boss that no data can be lost, due to failed hard drive, etc.

Answers

The ways of arranging the storage so that you can meet the specifications set by your boss:

RAID – (Redundant Array of Independent Disks)BackupCloud storage

The first method for organizing a storage system is RAID. It is one of the most reliable methods for protecting data from hard drive failure. The RAID system uses several hard drives and combines them into a single volume. Data is then written across the drives, thus ensuring that if one fails, there is no data loss.A backup is an excellent method to safeguard data against potential loss due to hardware or software failure. Your storage system should have a routine backup schedule that backs up critical data regularly. The use of cloud storage is increasing in popularity. Cloud storage is a great way to safeguard data against loss due to hardware or software failure.

Learn more about RAID: https://brainly.com/question/28963056

#SPJ11

on initial climbout after takeoff and with the autopilot engaged, you encounter icing conditions. in this situation you can expect

Answers

If you encounter icing conditions during climb-out after takeoff and with the autopilot engaged, you can expect the autopilot to adjust the aircraft's pitch and power to maintain a constant airspeed, which may not be sufficient to prevent ice buildup on the wings and other critical surfaces.

What is the explanation for the above response?

In such a situation, it is essential to take immediate action to ensure the safety of the flight.

This may include turning off the autopilot and manually adjusting the pitch and power to maintain a safe speed and altitude, activating the aircraft's anti-icing systems, and communicating with air traffic control to request clearance to climb to a higher altitude or change your flight path to avoid the icing conditions.

Learn more about Autopilot at:

https://brainly.com/question/20372893

#SPJ1

5. A continuous hot rolling mill has two stands. Thickness of the starting plate = 1.0 in. and width = 12.0 in. Final thickness is to be 0.5 in. Roll radius at each stand = 10 in. Rotational speed at the first stand = 20 rev/min. Equal drafts of 0.25 in. are to be taken at each stand. The plate is wide enough relative to its thickness that no increase in width occurs. Under the assumption that the forward slip is equal at each stand determine (a) speed v, at each stand and (b) forward slip s. (c) also determine the exiting speeds at each rolling stand if the entering speed at the first stand is 85 ft/min.​

Answers

Answer:

(a) To determine the speed v at each stand, we can use the relationship between the forward slip, rotational speed, and rolling speed:

rolling speed = rotational speed × (1 - forward slip)

At the first stand, the thickness reduction is:

thickness reduction = draft / starting thickness = 0.25 / 1.0 = 0.25

The final thickness after the first stand is:

final thickness = starting thickness - thickness reduction = 1.0 - 0.25 = 0.75

The speed at the first stand is:

v1 = (π × 10^2 × 20) / (12 × 0.75) = 139.63 ft/min

At the second stand, the thickness reduction is again 0.25, and the final thickness is 0.5. The speed at the second stand is:

v2 = (π × 10^2 × 20) / (12 × 0.5) = 209.44 ft/min

(b) To determine the forward slip, we can use the formula:

forward slip = (rotational speed - rolling speed) / rotational speed

At the first stand:

forward slip1 = (20 - 139.63) / 20 = -5.98

At the second stand:

forward slip2 = (20 - 209.44) / 20 = -9.47

Note that the negative values indicate that the rolling speed is greater than the rotational speed, which is physically impossible. This suggests that the assumption of equal forward slip at each stand is not valid.

(c) The exiting speed at each rolling stand can be determined using the same formula as in part (a), but with the entering speed at the previous stand as the rolling speed:

At the first stand, entering speed = 85 ft/min:

v1 = 85 × (1 - (-5.98)) = 541.88 ft/min

At the second stand, entering speed = v1:

v2 = v1 × (1 - (-9.47)) = 922.57 ft/min

TRUE/FALSE. Estimation is more accurate if done for the total time versus dividing the project into bite-size pieces and estimating each piece.

Answers

The given statement "Estimation is more accurate if done for the total time versus dividing the project into bite-size pieces and estimating each piece" is False because the main reason behind dividing the project into bite-size pieces and estimating each piece is to get a more accurate estimate of the project.

By dividing the project into bite-size pieces and estimating each piece, we can know about the time, effort, resources required for each piece. This information helps us in getting an accurate estimate of the project. In the case of a large project, it is challenging to estimate the total time required for the project.

It is because there may be many uncertainties, risks, dependencies that can affect the project. In such cases, dividing the project into smaller pieces and estimating each piece helps us to consider these uncertainties, risks, dependencies, etc. and get an accurate estimate of the project.

So, the given statement that "Estimation is more accurate if done for the total time versus dividing the project into bite-size pieces and estimating each piece" is False.

For such more question on Estimation:

https://brainly.com/question/30543546

#SPJ11

which of the following need to be configured for a computer to operate on a modern network? check all that apply

Answers

Depending on the particular network requirements and setups, a computer may need to be configured for IP address and all of the aforementioned options in order to function on a modern network.

To have a computer network, you need which of the following?

Switches, routers, and access points are required for a computer network to function. Switches use cables to connect to networks in homes or offices and aid with internal security for computers and other devices.

What is the procedure by which a DHCP-enabled client tries to obtain network configuration data known as?

a DNS server and a gateway. DHCP in Use. the method by which a client set up to use DHCP makes an effort to obtain network configuration. DHCP discovery is the process of gathering data. DHCP's discovery procedure.

To know more about IP address visit:-

https://brainly.com/question/16011753

#SPJ1

provide formulas for x(t)and y(t)that could possibly represent the parametric curve (x(t),y(t)). explain how your formulas could possibly represent the parametric curve (x(t),y(t)).

Answers

The given problem is asking for the formulas of x(t) and y(t) that could represent the parametric curve (x(t), y(t)).

What is parametric curve?

Parametric curve is the curve that is defined by equations of the form [tex]x=f(t)[/tex] , [tex]y=g(t)[/tex] where t is the parameter.

So, for a given value of t, x and y coordinates can be found by plugging in that value of t. Different values of t will give different points on the curve.

To find the formulas for x(t) and y(t), the following steps can be used:

Step 1: Identify the shape of the curve. Based on the shape of the curve, we can come up with the equation of the curve.

Step 2: Break the curve into x(t) and y(t) components.

Step 3: Choose a parameter to represent the curve. Typically, we use t as the parameter.

Step 4: Determine the x(t) and y(t) components of the curve based on the chosen parameter.

Step 5: Write the equations of x(t) and y(t).

The equations can be simple linear equations or more complex nonlinear equations.

For example, consider a circular path. The equation of a circle can be represented as [tex](x-a)^2+(y-b)^2=r^2[/tex]

Where a and b represent the coordinates of the center of the circle, and r is the radius of the circle.

To find x(t) and y(t), we can rewrite the equation of the circle as: [tex]x=a+r cos(t)[/tex] and [tex]y=b+r sin(t)[/tex]

where t is the parameter.

So, for different values of t, we can get different points on the circle.

Learn more about Parametric curve here:

https://brainly.com/question/30482587

#SPJ11

3) A steel pin supporting a gondola lift is subjected to an axial stress expected to be 51 ksi with a standard deviation of 3 ksi. The steel has a Sy of 60 ksi and S. of 80 ksi, both with a standard deviation of 5 ksi. Material yielding is considered a failure and will require part replacement. An ultimate failure will result in the loss of 20 human lives. a) If there are 100,000,000 of these parts in service, how many lives would you predict to be lost? b) The cost of this part varies linearly with the cross-sectional area (for the same length part, to double the cross- sectional area requires twice as much steel and twice the cost) The stress experienced by this part varies inversely and linearly with the cross-sectional area (you can imagine part as being in pure tension). By what fraction would you increase the cost of the part?

Answers

The cost should be increased by 50% or 0.5 fraction.

If there are 100,000,000 of these parts in service, how many lives would you predict to be lost?

The cost of this part varies linearly with the cross-sectional area (for the same length part, to double the cross-sectional area requires twice as much steel and twice the cost) The stress experienced by this part varies inversely and linearly with the cross-sectional area (you can imagine part as being in pure tension).

By what fraction would you increase the cost of the part?

The probability of the steel pin to fail, P(f) can be computed by the following formula:

P(f) = P(S> Sy)

Where P(S> Sy) is the probability of stress exceeding the yield stress. The value of P(S> Sy) can be calculated as follows:

Z= (S - μ)/σZ = (60 - 51)/3= 3P(S> Sy) = P(Z > 3) = 0.0013

Z= (S - μ)/σZ = (80 - 51)/5= 5.8P(S> Sut) = P(Z > 5.8) = 0.0000041

The probability of yielding (failure) can be computed as:

P(failure) = P(Sy < S < Sut) = P(S > Sy) - P(S > Sut) = 0.0013 - 0.0000041 = 0.001296

The number of parts in service = N = 100,000,000

Expected number of failures = N * P(failure) = 100,000,000 * 0.001296 = 129,600 lives are expected to be lost

The cost of the part is proportional to the cross-sectional area, A. If we assume the cross-sectional area to be doubled, then the cost will be doubled too.The stress, S is inversely proportional to A.

Therefore if A is doubled, then S will reduce by half (1/2) that is:S1/S2 = A2/A1S2= S1 (A1/A2)S2= 51 ksi (2/1)S2= 102 ksi

The fraction by which we should increase the cost is given as:

(Cost at S1/Cost at S2)= (Area at S1/Area at S2)= (1/2) = 0.5

Therefore, the cost should be increased by 50% or 0.5 fraction.

Learn more about Fraction:

brainly.com/question/6201432

#SPJ11

Compute the terminal velocity of a spherical raindrop of diameter 0.05 inches. Assume it falls through air at standard sea level conditions DISCUSSION: How does the terminal velocity vary with droplet diameter?

Answers

To compute the terminal velocity of a spherical raindrop of diameter 0.05 inches, we must use Stoke's law.

What is the definition of terminal velocity?

The terminal velocity of a freely falling object is the speed at which it stops accelerating due to the force of air resistance acting on it, such that its acceleration becomes zero. The terminal velocity is a velocity that is reached when the force of air resistance balances the force of gravity on an object.

The terminal velocity of a spherical raindrop is given by:

[tex]v=2gr^2(p_s-p_f)/9(\eta)[/tex]

where v is the terminal velocity of the raindrop, g is the acceleration due to gravity (9.81 m/s²), r is the radius of the raindrop, [tex]p_s[/tex] is the density of the sphere (1,000 kg/m³ for water), [tex]p_f[/tex] is the density of the fluid through which the raindrop is falling (1.29 kg/m³ for air at standard sea level conditions), and η is the dynamic viscosity of the fluid (18.6 × 10⁻⁶ kg/(m·s) for air at standard sea level conditions).

Diameter variation with terminal velocity: As the diameter of the raindrop increases, its terminal velocity also increases. Larger raindrops have a higher terminal velocity than smaller raindrops due to the increased force of gravity acting on them. However, when a raindrop becomes too large, it will split into smaller droplets due to surface tension.

Learn more about terminal velocity here:

https://brainly.com/question/30466634

#SPJ11

Although many organizations prefer to use a single technology stack, it is not always viable because of various application needs. However, it is important to understand all the pieces of technology involved with certain technology stacks. The two most common are Microsoft .NET and Java-based technologies. In the selection of either, there are specific operating systems, databases, programming languages, development tools and servers that are used with each technology stack.Research all the necessary technical standards for a technology stack and make recommendations of what must be included for an organization to use that technology stack for software development.

Answers

An organization must include the following technical standards: operating systems, databases, programming languages, development tools, and servers that are used with each technology stack.

To use a technology stack for software development, an organization needs to include the following technical standards:

Operating System - A technology stack requires a specific operating system, as it is dependent on the underlying system that is used. An organization should choose the operating system that is most suitable for its needs.

Databases - It is important to select a database that supports the specific technology stack. For example, for Java-based technologies, Oracle is a commonly used database.

Programming Languages - Programming languages are an important aspect of a technology stack, and the organization should choose the language that is best suited for its needs.

Development Tools - An organization must choose development tools that support the specific technology stack that is being used. These tools should be easy to use and provide support for debugging and testing.

Servers - A technology stack requires specific servers to run on. An organization must choose the server that is most suitable for its needs, such as Apache Tomcat for Java-based technologies.

In conclusion, to use a technology stack for software development, an organization must include the following technical standards: operating systems, databases, programming languages, development tools, and servers that are used with each technology stack.

To know more about technology stack:https://brainly.com/question/23504399

#SPJ11

Which of these is NOT one of the preventive measures aimed at reducing motor vehicle accidents that are caused by poor decision making in young drivers?
driver "buddy systems"

Answers

None of the following is a preventive measure aimed at reducing motor vehicle accidents caused by poor decision-making in young drivers: driver “buddy systems”, increased penalties for violations of driving laws, or driver’s education classes.

The most effective measures to reduce motor vehicle accidents are for young drivers to be taught the rules of the road and to develop good decision-making skills. These measures include: using defensive driving techniques, limiting distractions while driving, avoiding driving while impaired, and understanding the risks of speeding or aggressive driving. Young drivers should also be taught the importance of wearing seatbelts, checking tire pressure and vehicle maintenance, and having emergency preparedness kits in their vehicles. Educating young drivers on these safety measures is essential to reduce motor vehicle accidents.

To learn more about Buddy :

https://brainly.com/question/30908546

#SPJ11

iintellectual property rights may be legally protected in several ways. which of the following answer options is not one of the ways of protecting intellectual property?

Answers

The following answer option is not one of the ways of protecting intellectual property: Planting evidence in another company's office.

Intellectual property refers to creative works or inventions that have a commercial purpose or application. Intellectual property is classified as either industrial property or copyright. Patents, trademarks, industrial designs, and geographical indications are examples of industrial property. Copyright refers to literary and artistic works like books, films, and music, as well as architectural and graphic designs.The legal protection of intellectual property rights:There are various ways to legally protect intellectual property rights, including:PatentTrademarkCopyrightTrade SecretIndustrial Design Plant Varieties.

This answer the question: " which of the following answer options is not one of the ways of protecting intellectual property?"

Learn more about Intellectual property: https://brainly.com/question/1078532

#SPJ11

Add some source code files to compile. Output a half pyramid of stars with a height determined by the user. If the user enters a number less than one, exit. Hint: See chapter 4's discussion of this type of problem. Test Case 1 Standard Input 5 Required Output Enter a height in * in in In *** n ***** in Standard Input 10 Required Output Enter a height\n in In ** ***** I\n ***** in ***** in \n n in

Answers

A pattern program which has a pyramid shape is called the pyramid program in Java.

CODE

package javaprograms;

import java.util.Scanner;

public class PatternHalfPyramid {

   

   public static void halfPyramid(int n)  { 

  

       int i, j;  

       for(i=0; i<n; i++)  { 

           System.out.print(" "); 

           for(j=0; j<=i; j++)  {  

               System.out.print("* "); 

           }           

           System.out.println(); 

     } 

   }

   //    Main Function

   public static void main(String args[]) {  

  

       Scanner scan = new Scanner(System.in);

       System.out.print("Enter a height : ");

       int num = scan.nextInt(); 

       if (num >0) {

           halfPyramid(num); 

       }

       else {

           System.out.print("Try Again! Kindly enter height more than 0 ");

           System.exit(0);

       }

   } 

}

To know more about Pyramid, click on the link :

https://brainly.com/question/13057463

#SPJ1

Suppose that the current value of PC is 0x00004000. Can we use a single jump instruction to go to PC= 0x20014924?(if yes, write the jump instruction and show the value of the immediate field in Hex. If not, use a combinations of instructions to do so and show the immediate values in Hex)

Answers

No, we cannot use a single jump instruction to go from PC = 0x00004000 to PC = 0x20014924, since the jump instruction can only jump to a location within a certain range of the current PC value.

To jump to 0x20014924, we would need to use a combination of instructions, such as a branch instruction and a jump instruction. Here is an example of how we could do this:

Add the immediate value 0x20010924 to the current PC value 0x00004000 using the addi (add immediate) instruction:

addi $t0, $zero, 0x20010924

add $t0, $t0, $zero

Branch to the new address using the jalr (jump and link register) instruction:

jalr $zero, $t0, 0

The immediate value for the addi instruction would be 0x20010924, and the immediate value for the jalr instruction would be 0, since we want to jump to the address stored in register $t0.

To know more about range click here:

brainly.com/question/28135761

#SPJ4

(15 points) Case hardening of a steel (Fe-C alloy) gear with initial concentration of 0.10 wt.% C is accomplished by raising the composition 7 mm below the surface to at least 0.35 wt% C. An engineer has proposed elevating the surface concentration to 1.10 wt% C for 307.787 hours at 1,000 °C. Note that the diffusion coefficient of carbon in steel at 1,000 °C is 1.6x10-1 m²/s. What is the concentration of carbon in the steel at a distance 8 mm from the surface? Note: If point is close to tabulated value you can use value from table and avoid linear interpolation.

Answers

The concentration of carbon in the steel at a distance of 8 mm from the surface is 0.224 wt%.

Here's a step-by-step explanation:
1. First, convert the distance from the surface from millimeters to meters: 8 mm = 0.008 m.
2. Calculate the diffusion parameter (z) by dividing the distance by the square root of the diffusion coefficient multiplied by time: [tex]z = x / \sqrt(Dt)[/tex]

[tex]z = 0.008 m / \sqrt(1.6*10^(-1) *307.787 *3600)[/tex]

[tex]z = 0.008 / \sqrt(1.6*10^(-1) * 307.787 * 3600)[/tex]

[tex]z =0.112[/tex]
3. Consult the error function table to find the corresponding value for z ≈ 0.112, which is erf(z) ≈ 0.124.
4. Calculate the concentration of carbon at the specified depth using the initial concentration, surface concentration, and error function value:

[tex]C(x) = C_(initial) + (C_(surface) - C_(initial)) * erf(z)[/tex]

[tex]C(x) = 0.10 + (1.10 - 0.10 ) * 0.124[/tex]

[tex]C(x) = 0.10 + 1.00 * 0.124[/tex]

C(x)≈ 0.224 wt.%
The concentration of carbon in the steel at a distance of 8 mm from the surface is approximately 0.224 wt.%.

Learn more about steel at:

https://brainly.com/question/26217574

#SPJ11

Define the EvenNumber class for representing an even number. The class contains:
A data field value of the int type that represents the integer value stored in the object.
A no-arg constructor that creates an EvenNumber object for the value 0.
A constructor that constructs an EvenNumber object with the specified value.
A function named getValue() to return an int value for this object.
A function named getNext() to return an EvenNumber object that represents the next even number after the current even number in this object.
A function named getPrevious() to return an EvenNumber object that represents the previous even number before the current even number in this object.
Draw the UML diagram for the class. Implement the class. Write a test program that creates an EvenNumber object for value 16 and invokes the getNext() and getPrevious() functions to obtain and displays these numbers.
A. (The EvenNumber class) Define the EvenNumber class for representing an even number. The class contains:  A data field value of the int type that represents the integer value stored in the object.  A no-arg constructor that creates an EvenNumber object for the value 0.  A constructor that constructs an EvenNumber object with the specified value.  A function named getValue() to return an int value for this object.  A function named getNext() to return an EvenNumber object that represents the next even number after the current even number in this object.  A function named getPrevious() to return an EvenNumber object that represents the previous even number before the current even number in this object. Draw the UML diagram for the class. Implement the class. Write a test program that creates an EvenNumber object for value 16 and invokes the getNext() and getPrevious() functions to obtain and displays these numbers. B. Revise the EvenNumber class in Programming Exercise 2A to implement the preincrement, predecrement, postincrement, and postdecrement operators for getNext() and getPrevious() functions. Write a test program that creates an EvenNumber object for value 16 and invokes the ++ and -- operators to obtain next and previous even numbers.
B.Revise the EvenNumber class in Programming Exercise 2A to implement the preincrement, predecrement, postincrement, and postdecrement operators for getNext() and getPrevious() functions. Write a test program that creates an EvenNumber object for value 16 and invokes the ++ and -- operators to obtain next and previous even numbers.

Answers

Answer:

#include <iostream>

using namespace std;

class EvenNumber

{

   private:

   int integrer;

   

   public:

   EvenNumber ()

   {

       integrer=0;

   }

   EvenNumber (int number)

   {

   integrer=number;

   }

   

   int getvalue ()

   {

       return integrer;

   }

   int getnext ()

   {

       return integrer+2;

       

   }

   int getprevious ()

   {

       return integrer-2;

       

   }

};

int main () {

   EvenNumber sixteen(16);

   cout<<"The value is: "<<sixteen.getvalue()

   <<" the next even number is: "<<sixteen.getnext()<<

   " and the previous number is: "<<sixteen.getprevious();

   return 0;

}

Explanation:

In JavaGiven the array-based list (20, 30, 40, 50), what will the new array look like after the following operations?
ArrayListPrepend(list, 10)
ArrayListSearch(list, 25)
ArrayListRemoveAt(list, 2)
ArrayListSearch(list, 40)

Answers

The new array will look like this after the given operations: [10, 20, 50].

ArrayListPrepend(list, 10): In this operation, 10 is added at the beginning of the list, which makes the new array (10, 20, 30, 40, 50). ArrayListSearch(list, 25): In this operation, we try to find the element 25 in the list. Since there is no such element in the list, the function will return -1. So, the array remains unchanged as (10, 20, 30, 40, 50). ArrayListRemoveAt(list, 2): In this operation, the element at index 2 (i.e. 30) is removed from the list. So, the new array becomes (10, 20, 40, 50). ArrayListSearch(list, 40): In this operation, we try to find the element 40 in the list. It is present at index 2. So, the function will return 2. The array remains as (10, 20, 40, 50).Therefore, the new array will look like this after the given operations: [10, 20, 50].

Learn more about ArrayList: https://brainly.com/question/20464124

#SPJ11

What is the minimum number of electoral votes needed to win a presidential election?

Answers

Answer:

Explanation:

270

The contribution margin ratio is 20% for Crowne Company and the break-even point in sales is $290,000. If Crowne Company's target operating profit is $69,000, sales would have to be:

Answers

Answer:

First, we need to calculate the contribution margin:

Contribution margin = Sales x Contribution margin ratio

Contribution margin = Sales x 0.2

We also know that the break-even point is $290,000, which means:

Contribution margin = Fixed costs + Operating profit

Contribution margin = $290,000 + $69,000

Contribution margin = $359,000

Now we can set up the equation to solve for sales:

Sales x 0.2 = $359,000

Sales = $359,000 / 0.2

Sales = $1,795,000

Therefore, Crowne Company would have to generate $1,795,000 in sales to achieve a target operating profit of $69,000 with a contribution margin ratio of 20%.

What vehicles are often required to shuttle fans to and from satellite parking lots?CarsTrainsBusesAll of the Above

Answers

C. Buses

Hope this helps

zone bit recording is how disk manufacturers ensure that a platter's outer tracks store as much data as possible.

Answers

Zone bit recording is how disk manufacturers ensure that a platter's outer tracks store as much data as possible. Zone bit recording (ZBR) is a disk layout method for accommodating more data on a single hard disk platter.

It works by allocating extra sectors (the smallest unit of data on a hard disk) to the outer tracks on a hard disk platter, which store data more efficiently than inner tracks. Because the data is more tightly packed together on the outer tracks, ZBR is often used in conjunction with smaller track widths, which are used to improve data throughput.

ZBR, when used in conjunction with other disk design enhancements such as smaller track widths, allows for the allocation of more data to the outer tracks on a hard disk platter, resulting in increased data storage capacity for the same physical platter size. In addition, ZBR improves data throughput by decreasing the amount of time required for disk heads to access data on the outer tracks, resulting in faster read and write times for files stored in these areas of the disk.

The primary disadvantage of ZBR is that it necessitates a non-linear hard disk drive layout, which makes file fragmentation and drive maintenance more complex. It can also make data recovery more difficult, especially if data on the outer tracks becomes corrupted or damaged in some way.

For more such questions on Zone bit recording

https://brainly.com/question/30331112

#SPJ11

A boy stands out at the end of the diving board, which is supported by two springs A and B, each having a stiffness of k = 15 kN/m. In the position shown the board is horizontal. Assume the spring A is fixed to both the ground and the board, and spring B is fixed to the ground only.If the boy has a mass of 40 kg, determine the angle of tilt which the board makes with the horizontal after he jumps off. Neglect the weight of the board and assume it is rigid.

Answers

Angle of tilt which the board makes with the horizontal after he jumps off is 0.33 radians.

The angle of tilt which the board makes with the horizontal after the boy jumps off can be determined using the following formula:

Angle of tilt = (Force of spring A / Mass of boy) x (1/ Stiffness of spring A)

Force of spring A = k x (deflection of spring A)

Deflection of spring A = (Mass of boy x 9.8 m/s²) / (2 x Stiffness of spring A)

Substituting all values,

Angle of tilt = (15 kN/m x (40 kg x 9.8 m/s²) / (2 x 15 kN/m)) x (1/15 kN/m)

Angle of tilt = (40 kg x 9.8 m/s²) / (2 x 15 kN/m)

Angle of tilt = 0.33 radians.

Learn more about "Angle of tilt" and "mass" at : https://brainly.com/question/27316884

#SPJ11

which of the following is a probable cause of relay-controlled equipment failing to start when the contactor is closed?

Answers

One contact not closing  is a probable cause of relay-controlled equipment failing to start when the contactor is closed

   

   

Why is a contactor used?

Now you may ask, why do we need to use a contactor? Can't we just connect the motor to the PLC? The simple answer is no.Why? Because you don't want to connect a high-voltage electric motor directly to your expensive PLC. If there are any electric surges on the motor's side, the PLC cards will be damaged.Instead, we use a contactor to connect the PLC to the motor in an indirect and safe manner. What do we mean by "indirectly," you may wonder. All contactors, after all, have a low voltage coil. The PLC output is connected to this coil. This coil is typically powered by a 24-volt DC signal.When the coil is turned on, an electromagnetic field is created.

To know more about Contactor, click on the link :

https://brainly.com/question/28146701

#SPJ1

The Complete Question is:- Which of the following is a probable cause of relay-controlled equipment failing to start when the contactor is closed?

A bead with a mass of 0.25 kg is released from rest at A and slides down and around the fixed smooth wire. Determine the force N between the wire and the bead as it passes point B. 0.6 m 45 0.15 m Problem 3/145

Answers

The force N between the wire and the bead as it passes point B is 3.135 N.

The free body diagram of the mass (bead) can be represented as follows:

Here, T is the tension in the string, N is the normal force exerted by the wire on the bead, mg is the gravitational force acting on the bead and a is the centripetal acceleration. From the figure given in the question, we can write the following: Normal force is zero at points A and C. Therefore, the normal force is only present at point B. Let's write the equation for point B. The forces acting on the bead are the normal force N and gravitational force mg (since there is no tension in the wire at point B):N - mg = ma Equating the forces we get: N - (0.25 kg × 9.8 m/s²) = (0.25 kg × 2.74 m/s²)N = 0.25 kg × (9.8 m/s² + 2.74 m/s²)N = 0.25 kg × 12.54 m/s²N = 3.135 N

Learn more about centripetal acceleration

brainly.com/question/14465119

#SPJ11

A bett is tensioned to 704N whilst stationary in a belt pulley system. Calculate the tension in Newtons for the taught side given that the wheel is184 mmdiameter and5 kWof power are being transmitted at334rev/min. 1.480 .92 margin of error⋯2%Question 2 The engineering wrapped a belt around a drum 2.00 times, then applies a195 Nweight to one of the ends. It is calculated by a technician the coefficient of friction is 0.36 . What is the maximum weight inkNan the other end of the pulley system before slippage occurs.

Answers

The tension in Newtons for the taught side is 104.38 N. The maximum weight that the other end of the pulley system can bear before slippage occurs is 6.094 kN

Given that a belt is tensioned to 704 N whilst stationary in a belt pulley system. the wheel is 184 mm in diameter and 5 kW of power is being transmitted at 334 rev/min.

The formula to calculate the tension in the taught side of a belt pulley system is as follows:

T1 = (P×60)/(2×π×N) + (μ×P×60)/(2×π×N)

Where T1 is the tension in the taught side of the belt pulley system.

P is the power transmitted in kW.

N is the speed of rotation in rpm.

μ is the coefficient of friction in the belt pulley system.

Substituting the given values in the above equation,

T1 = (5×60)/(2×3.14×334) + (0.92×5×60)/(2×3.14×334)

T1 = 95.9 + 8.48T1 = 104.38 N (approx)

Therefore, the tension in Newtons for the taught side is 104.38 N (approx)

2: A technician calculated the coefficient of friction as 0.36 when an engineer wrapped a belt around a drum 2.00 times and then applied a 195 N weight to one of the ends.

The maximum weight that the other end of the pulley system can bear before slippage occurs can be calculated as follows:

μ = (T2 - T1)/W

Where μ is the coefficient of friction in the belt pulley system.

T1 is the tension in the tight side of the pulley system.

T2 is the tension in the slack side of the pulley system.

W is the weight attached to the slack side of the pulley system.

Substituting the given values in the above equation,0.36 = (T2 - 195)/W

Assuming T2 is greater than T1, the total tension can be calculated as follows:

T2 = 2T1T2 = 2(W + 195)W can be calculated as follows:

0.36W = 2W + 3900.64W = 3900W = 6093.75 N (approx)

Therefore, the maximum weight that the other end of the pulley system can bear before slippage occurs is 6.094 kN (approx).

To know more about belt pulley system:https://brainly.com/question/29718602

#SPJ11

1. The tension in Newtons for the taught side is 493.17 N. 2. The maximum weight in kN the other end of the pulley system before slippage occurs is 0.1404 kN.

1. Tension = 704 N
Diameter of wheel (D) = 184 mm = 0.184 m
Power (P) = 5 kW = 5000 W
Speed (N) = 334 rpm
We need to find the tension in Newtons for the taught side.
The formula for tension in the belt pulley system is:

T1 - T2 = (P x 60) / (2πN) Here, T1 is the tension in the tight side and T2 is the tension in the slack side.
Substitute the given values in the above formula, we get:
T1 - T2 = (5000 x 60) / (2π x 334)T1 - T2 = 282.33N......(1)
As the bett is tensioned to 704N whilst stationary, we have T1 + T2 = 704N......(2)
Adding equations (1) and (2), we get:2T1 = 986.33NT1 = 493.17 N

Therefore, the tension in Newtons for the taught side is 493.17N.

2. Number of turns (n) = 2
Applied weight (W) = 195 N
Coefficient of friction (µ) = 0.36
We need to find the maximum weight in kN at the other end of the pulley system before slippage occurs.
The formula for maximum weight is:
Maximum weight (Wmax) = µ x n x W......(1)
Substitute the given values in the above formula, we get:
Wmax = 0.36 x 2 x 195

Wmax = 140.4 N

As the required answer is in kN, divide the above answer by 1000.

Wmax = 0.1404 kN.

Therefore, the maximum weight in kN the other end of the pulley system before slippage occurs is 0.1404 kN.

To learn more about "tension": brainly.com/question/11348644

#SPJ11

the need to back up important data before installing new hardware is an example of the following constraint(s):

Answers

The need to back up important data before installing new hardware is an example of the following constraint(s): time constraint and cost constraint.

Constraints, also known as limitations or restrictions, are a set of parameters that limit the possible solutions to a specific issue or problem. Constraints come in a variety of forms, and the importance of a given constraint is determined by the problem being addressed. The need to back up important data before installing new hardware is an example of the following constraints:

Time constraint- This implies that there is a limited amount of time available to complete a task, and as a result, we must work within that time frame to accomplish our objectives. In this scenario, a time restriction is present because the installation of new hardware must be completed in a certain amount of time, necessitating the need to back up data before starting the procedure.

Cost constraint- This refers to the financial limits that restrict the amount of money available for the solution's execution. If the cost of backing up the data is too high, it may prohibit the new hardware installation. As a result, it's crucial to consider the cost of implementing a solution when dealing with a problem.

For more such questions on hardware

https://brainly.com/question/28494136

#SPJ11

what were the gargoyles on a gothic cathedral are there _____.

Answers

Gargoyles on a Gothic cathedral are decorative sculptures, typically with the form of a grotesque animal or person, that are designed to convey water away from the building's walls through a spout.

what do you called Generally uncontrolled intersections are found in?

Answers

Generally uncontrolled intersections are found in areas with low traffic volume or in rural areas where the intersection of two roads does not warrant the installation of traffic signals or stop signs.

These intersections are called uncontrolled because they do not have any signs, signals, or other traffic control devices to regulate the flow of traffic.

Drivers approaching an uncontrolled intersection must use caution and be prepared to yield to other vehicles or pedestrians as necessary. The right of way at an uncontrolled intersection typically goes to the vehicle on the right, but this may vary depending on local traffic laws and regulations. Drivers should also be aware of any potential hazards such as blind spots, obstacles, or uneven road surfaces that may affect their ability to safely navigate the intersection.

To know more about traffic click here:

brainly.com/question/28043913

#SPJ4

When using THHN stranded copper conductors what are the minimum size branch circuit conductors required to operate a 240 volt Single Phase 5 HP motor with 75 terminations /Select one a 12 AWG b.10 AWG c. 8 AWG d. 6AWG

Answers

According to the National Electrical Code, the minimum size branch circuit conductors required for this application are 10 AWG.

What is the minimum size branch circuit conductor?

When using THHN stranded copper conductors, the minimum size branch circuit conductors required to operate a 240-volt single-phase 5 HP motor with 75 terminations are 10 AWG. What is THHN wire?

THHN wire is made up of several copper wires and is widely used in construction, appliance wiring, and general electrical purposes. THHN cables are available in a variety of colors and sizes, making them ideal for almost every application. What is the definition of Stranded Copper?

A copper wire that is made up of several smaller wires that are twisted together to create a single wire is known as stranded copper. The strands of wire are often twisted around each other to make them stronger, and the more strands a cable has, the more flexible and durable it is. This cable is also less likely to break under stress because of its flexibility.What is meant by a conductor?A conductor is a substance or object that transports electrical energy, heat, or sound. The word "conduct" means "to carry."

The movement of electric charges through a conductor is responsible for the transmission of electrical power. Copper, silver, gold, and aluminum are examples of good electrical conductors. In comparison to other conductive metals, copper is the most widely used due to its low cost, high conductivity, and excellent ductility.

Therefore, it is a widely utilized material in power transmission and distribution cables, electrical equipment, and electromagnets in the electrical industry. What is the minimum size branch circuit conductors?

According to the table 430.248 of the National Electrical Code, the minimum size branch circuit conductors required to operate a 240-volt single-phase 5 HP motor with 75 terminations are 10 AWG. 10 AWG is the minimum size permitted for this application. Thus, option (b) 10 AWG is the right answer.

Learn more about: circuit conductor

brainly.com/question/28269880

#SPJ11

FILL IN THE BLANK._______ is a command-line function for viewing and setting wireless interface parameters and is common to nearly all version of Linux and UNIX.

Answers

"iwconfig" is used to configure wireless network interface parameters such as SSID, encryption key, and power management features, among other things.

This command is a part of the wireless-tools package and is normally available on most Linux distributions.To run the "iwconfig" command, you must first open a terminal window. The command is executed by typing "iwconfig" followed by the name of the wireless network interface you wish to manage. The basic syntax for running the "iwconfig" command is as follows: iwconfig [interface] [options]The [interface] parameter is the name of the wireless network interface that you want to configure. You can obtain a list of available wireless network interfaces by using the "ifconfig" command. If the [interface] parameter is omitted, "iwconfig" will show the parameters for all of the available wireless interfaces on your system. Once you have specified the [interface] parameter, you can specify any number of [options] to configure the wireless interface.The "iwconfig" command is a valuable tool for managing wireless networks on Linux and UNIX systems.By using this command, you can configure your wireless interface to operate more efficiently, as well as troubleshoot any problems that you may encounter while using your wireless network.

for more such question on parameter

https://brainly.com/question/29673432

#SPJ11

Which of the following statements is correct?
a. In pure metals, dendritic growth represents the vast majority of the total growth.
b. When solid crystals form from a liquid, heat is absorbed.
c. The temperature of the liquid ahead of the solidification front is less than the freezing temperature.
d. Planar growth occurs by the movement of a smooth solid-liquid interface into the liquid

Answers

The correct statement is "When solid crystals form from a liquid, heat is absorbed." The correct option is B.

What is solidification?

Solidification is the process of transforming a liquid or a gas into a solid. The structure and properties of the solidified body are controlled by the manner in which the transformation occurs. Solidification is usually accompanied by a reduction in volume, a rise in density, and a decrease in entropy.

The liquid freezes when the temperature reaches the freezing point. When the liquid is frozen, the temperature is lower than the melting point of the substance. When a liquid freezes, it releases heat energy.

When solid crystals form from a liquid, heat is absorbed. Arrangement of crystals during solidification Planar growth occurs when the smooth interface moves into the liquid, and dendritic growth occurs when the crystal branches out in various directions. Planar growth occurs when there is an even, stable interface with the solid and liquid phases.

The interface's smoothness is due to the absence of any differences or disturbances that can cause the interface to fluctuate or oscillate.

The correct statement is Option B.

Learn more about Solidification here:

https://brainly.com/question/21278640

#SPJ11

Other Questions
you have $5,200 to deposit. regency bank offers 9 percent per year compounded monthly (.75 percent per month), while king bank offers 9 percent but will only compound annually. how much will your investment be worth in 17 years at each bank? natural groceries has a policy of not buying paper products, such as paper towels, from certain companies if they are made with rainforest wood. natural groceries is sending an economic message that it protests deforestation because of severe damage to the environment. this is an example of a . Bethany wants to build a wooden deck on her patio, which is in the shape of a parallelogram. The area of the patio is 580 ft2. Find the base. Round your answer to the nearest foot. Suppose that a list of numbers contains values [-4, -1, 1, 5, 2, 10, 10, 15, 30]. Which of the following best explains why a binary search should NOT be used to search for an item in this list?A. The list contains both positive and negative elements.B. The elements of the list are not sorted.C. The list contains an odd number of elements.D. The list contains duplicate elements. In Freuds theory which of the following is the center of conscious awareness in the personality that gives the individual the cognitive powers of judgment, memory, perception, and decision making?a. Idb. Superegoc. Libidod. Ego Write about lakunles attitude towards bride price when sitting at a wobbly desk and chair, people perceive others' relationships as less stable. this best illustrates H2O+C2H5OC2H5OH+OH NH4+OHNH3+H20Which of the two reactions is consistent with the Arrhenius theory of acids and bases Give the Bronsted Lowry definition of an acid and baseList each acid and its conjugate base for each of the reactions aboveChoose one of the above reactions and use Lewis structures to illustrate how it is consistent with the Lewis theory of acids and bases when is it most likely that articulatory knowledge of how speech sounds are made strongly helps speech perception Do consumers have an ethical responsibility to shop mindfully?Explain what that means.Topic Sentence:Detail 1Detail 2Detail 3 The prelab required you to use the impedance method to calculate the steady-state amplitude and phase (in degrees) of vc to an input vs = cos(2phi ft) where f-1000 Hz ( = 2phif). The results from the prelab are . Ao=_____Phase, =_____degrees The Babylonians established the alleged astrological correlations between star positions and personality characteristics by:a. conducting surveysb. doing experimentsc. assuming that such a relationship existedd. both A and B which of the following could be added to a solution of sodium acetate to produce a buffer?group of answer choiceshydrochloric acid onlypotassium acetate onlyacetic acid or hydrochloric acidacetic acid only there are two types of osteoporosis. classify each statement according to whether it is a characteristic of type 1 or type 2 osteoporosis Find the amount of the following ordinary annuities rounded to the nearest cent. Find the totAmount of DepositedInterestRate Time (Years) Amount of anAnnuityEarnedeach deposit$1050annually5%14 Assuming that bravo county receives all of its revenues from unassigned property taxes it is most likely to account for the activities of its police departments in its The world has been dangerous since WW I; however, the United States was mostly secure until the lasta. Day of the Cold War.b. Two centuries.c. Two decades.d. Two years. in 2020, jensen trucking reported a net income of $1,060,000, earnings per share on common stock of $5, and dividends on preferred stock of $200,000. if their income tax rate for 2020 was 30% and their payout ratio on common stock was 25%, how much did they pay in cash dividends for common stock in 2020? his yearly salary is $78000.Calculate his fortnightly income. (Use 26 fortnights in a year.)Fortnightly income = $ 2-Bromobutane is optically active but 1-Bromobutane is optically inactive. Why?2-bromobutane is a chiral molecule as it contains an asymmetric carbon atom therefore, it is optically active whereas 1-bromobutane is an achiral molecule as it does not contain an asymmetric carbon atom therefore it is optically inactive.