Determine the average emissivity of the surface and the rate of radiation emission from the surface, in W/m2.

When car tires are on hot pavement for too long, the pressure inside will increase and the volume within the tire will also increase. This happens because the heat causes the air molecules inside the tire to move faster and collide more frequently, increasing their pressure.

Additionally, the rubber of the tire expands slightly as it heats up, which can also increase the volume of air within the tire. It's important to regularly check tire pressure, especially during hot weather, to ensure safe driving conditions and avoid potential blowouts.

So, when car tires are on hot pavement for too long, the pressure inside will increase and the volume within the tire will also increase due to the heat causing the air molecules inside the tire to move faster and expand, leading to a rise in both pressure and volume.

To know more about pressure, refer

https://brainly.com/question/28012687

#SPJ11

The idea that the properties of the universe are finely tuned to support life and that any significant deviation from these properties would make life impossible is called the anthropic principle.

It suggests that the universe appears to be designed for the existence of intelligent life because any other type of universe would not allow the emergence and evolution of life forms. The anthropic principle is a controversial topic in the philosophy of science and cosmology, and there are different versions of it, including the weak anthropic principle and the strong anthropic principle.

Learn more about anthropic principle here:

https://brainly.com/question/31670787

#SPJ11

The rest energy of a 19.9 g piece of chocolate is approximately 1.791 terajoules.

To find the rest energy of a 19.9 g piece of chocolate, you'll need to use the equation E=mc^2, where E is the energy, m is the mass, and c is the speed of light.

Convert mass to kilograms (1 g = 0.001 kg)
19.9 g * 0.001 kg/g = 0.0199 kg

Find the speed of light (c) in m/s:
c = 3 x 10^8 m/s

Calculate the rest energy (E):
E = (0.0199 kg) * (3 x 10^8 m/s)^2

Simplify and convert the energy to terajoules (1 TJ = 10^12 J):
E = 1.791 x 10^15 J
E = 1.791 x 10^15 J / 10^12 J/TJ
E = 1.791 TJ

Thus, the rest energy is approximately 1.791 terajoules.

Learn more about "energy": https://brainly.com/question/13881533

#SPJ11

The total energy density of an electromagnetic wave is given by the equation:

u = ε0 E^2 / 2 + B^2 / (2μ0)

where u is the energy density, ε0 is the electric constant (permittivity of free space), E is the electric field strength, B is the magnetic field strength, and μ0 is the magnetic constant (permeability of free space).

If the value of the electric field in an electromagnetic wave were doubled, then the total energy density of the wave would increase by a factor of four. This is because the electric field strength term appears squared in the equation for energy density. Doubling the electric field strength would cause the energy density to increase by a factor of 2^2 = 4.To see this more clearly, we can rewrite the equation for energy density in terms of the electric field strength alone:

u = ε0 E^2 / 2 + (μ0/ε0) (E^2 / 2)

where the second term on the right-hand side represents the contribution to the energy density from the magnetic field strength (which is proportional to the electric field strength in an electromagnetic wave). If we double the electric field strength (E), then the energy density becomes:

u' = ε0 (2E)^2 / 2 + (μ0/ε0) [(2E)^2 / 2]

Simplifying this expression, we get:

u' = 4ε0 E^2 / 2 + (μ0/ε0) (4E^2 / 2)

u' = 2ε0 E^2 + 2μ0 E^2

u' = 2(E^2 / ε0)

This expression shows that doubling the electric field strength causes the energy density to increase by a factor of 2^2 = 4, as claimed above.

to know more about Electromagnetic wave please visit

https://brainly.com/question/31802774

#SPJ11

The velocity of the spaceship relative to the first planet is -0.8824c, which means it is moving away from the first planet at 0.8824 times the speed of light.


v = (v₁ + v₂) / (1 + (v₁ *v₂/c²))

where v is the relative velocity between two objects, v₁ is the velocity of the first object relative to a third reference point, v₂ is the velocity of the second object relative to the same reference point, and c is the speed of light.

In this case, we can consider the first planet as our reference point, and we have the following values:

- v₁ = 0 (since the first planet is stationary)
- v₂ = -0.75c (since the spaceship is approaching the second planet at 0.750c, which is a negative velocity relative to the second planet)
- c = 1 (since we're using units where the speed of light is 1)

Plugging these values into the formula, we get:

v = (0 + (-0.75)) / (1 + (0*(-0.75)/1²))
v = -0.8824c

Therefore, the velocity of the spaceship relative to the first planet is -0.8824c, which means it is moving away from the first planet at 0.8824 times the speed of light.

To know more about collision, refer

https://brainly.com/question/24915434

#SPJ11

The sound intensity level of a stadium crowd with an intensity of 3.50 W/m2 is 73.5 dB.

The sound intensity level (SIL) is a measure of the intensity of sound waves in decibels (dB).

To calculate the SIL, you can use the equation SIL = 10log(I/Io), where I is the intensity of the sound wave and Io is the reference intensity, which is 1 x[tex]10^-^1^2[/tex] W/m2.

Using the given intensity of 3.50 W/m2, we can calculate the SIL as SIL = 10log(3.50/1 x [tex]10^-^1^2[/tex]) = 73.5 dB.

This means that the sound made by the crowd in the stadium has a SIL of 73.5 dB, which is equivalent to the noise level of a vacuum cleaner or busy street traffic.

For more such questions on intensity, click on:

https://brainly.com/question/14252912

#SPJ11

When an electric field is applied to a shallow bath of vegetable oil, tiny bits of thread floating in the oil align with the field similar to compasses in a magnetic field. This occurs because the electric field induces polarization in the thread particles, causing them to develop positive and negative ends.

These charged ends align with the direction of the electric field, just as compass needles align with the magnetic field due to the interaction between their magnetic poles and the external magnetic field. When an electric field is applied to a shallow bath of vegetable oil, the electric field creates a force on the electrically charged particles in the oil. This force causes the particles to move and create a flow of oil. As the flow of the oil moves, it drags the tiny bits of thread along with it. The movement of the thread aligns with the electric field, similar to how compasses align with a magnetic field. This is because electric fields and magnetic fields are both types of fields that exert a force on particles, causing them to move or align in a particular direction. So, the tiny bits of thread in the oil align with the electric field just like compasses align with a magnetic field.

Learn more about the electric field here: brainly.com/question/15800304

#SPJ11

The average current in the 120 V power line to the house is 11.6 amps.

To find the average current in the 120 V power line to the house, we need to use the equation:

Power (P) = Voltage (V) x Current (I)

Rearranging the equation, we can solve for the current:

Current (I) = Power (P) / Voltage (V)

First, we need to convert the monthly energy usage from kilowatt-hours (kWh) to watt-hours (Wh):

1000 kWh x 1000 Wh/kWh = 1,000,000 Wh

Next, we need to find the average power usage per hour:

1,000,000 Wh / 720 hours per month = 1388.9 W

Using the above equation, we can now find the average current in the 120 V power line:

I = P/V = 1388.9 W / 120 V = 11.6 A

Know more about average current here:

https://brainly.com/question/13201381

#SPJ11

To determine the force needed to push out the pop-out hatch at a depth of 118 m below the surface, we need to consider the pressure exerted by the water on the hatch. At this depth, the water pressure is approximately 11.6 MPa (megapascals), which is equivalent to 11600 kPa (kilopascals) or 1.16 x 10^8 Pa (pascals).

To calculate the force needed to push out the hatch, we can use the formula:
Force = Pressure x Area
where Pressure is the water pressure at 118 m depth (1.16 x 10^8 Pa) and Area is the surface area of the hatch (1.70 m x 0.852 m = 1.4484 m^2).
Substituting these values into the formula, we get:
Force = 1.16 x 10^8 Pa x 1.4484 m^2
Force = 1.677 x 10^8 N

Therefore, the force needed to push out the pop-out hatch from a damaged submarine at a depth of 118 m below the surface is approximately 167.7 million Newtons.

To know more about approximately visit:-

https://brainly.com/question/31646509

#SPJ11

The magnetic field strength created at the center of the motor is 0.4306T.

To find the magnetic field strength created at the center of a circular loop, we can use the formula for the magnetic field strength of a current-carrying loop:

B = (μ₀ × I × N) / (2 × R)

where B is the magnetic field strength, μ₀ is the permeability of free space (4π × 10^(-7) Tm/A), I is the current (29.6 A), N is the number of turns (270), and R is the radius of the loop (0.098 m, since 9.8 cm = 0.098 m).

Now, let's plug in the values:

B = (4π × 10^(-7) Tm/A × 29.6 A × 270) / (2 × 0.098 m)

B = (3.711 × 10^(-6) T × 29.6 A × 270) / (0.196 m)

B = (3.0997 × 10^(-4) T × 270) / (0.196 m)

B = 0.084369 T / 0.196 m

B ≈ 0.4306 T

Therefore, the magnetic field strength created at the center of the loop is approximately 0.4306 T (Tesla).

To know more about magnetic, visit:

https://brainly.com/question/3160109

#SPJ11

182 bright fringes appear along the total length of the plates.

To determine the number of bright fringes appearing along the total length of the glass plates with a light of wavelength 549 nm, you need to follow these steps:

1. Calculate the total separation between the two glass plates at the end with the wire.
2. Find the difference in path length for each fringe.
3. Divide the total separation by the path length difference to find the number of fringes.

Step 1: Calculate the total separation between the two glass plates.
Total separation = radius of wire × 2 = 0.025 mm × 2 = 0.05 mm = 0.05 × 10⁻³m

Step 2: Find the difference in path length for each fringe.
Wavelength = 549 nm = 549 × 10⁻⁹ m
Since it is a single-slit interference pattern, the difference in path length for each fringe = wavelength / 2
Path length difference = 549 × 10⁻⁹ m / 2 = 274.5 × 10⁻⁹ m

Step 3: Divide the total separation by the path length difference to find the number of fringes.
Number of fringes = total separation / path length difference
Number of fringes = (0.05 × 10⁻³ m) / (274.5 × 10⁻⁹ m) ≈ 182

Therefore, approximately 182 bright fringes appear along the total length of the plates.

To know more about single-slit interference :

https://brainly.com/question/15694132

#SPJ11

Using the given information, we can calculate the total energy stored in the electric field of the parallel-plate capacitor.

The capacitor has a diameter of 2.60 cm (0.026 m) and a spacing of 0.400 mm (0.0004 m). It is charged to 300 V. First, we need to find the capacitance (C) using the formula C = ε₀ * A / d, where ε₀ is the vacuum permittivity (8.85 × 10⁻¹² F/m), A is the area of the plates, and d is the spacing between the plates.

The area A = π * (diameter / 2)² = π * (0.026 / 2)² = 5.31 × 10⁻⁴ m².

Now, we can find the capacitance: C = (8.85 × 10⁻¹² F/m) * (5.31 × 10⁻⁴ m²) / (0.0004 m) = 1.17 × 10⁻¹¹ F.

Next, we'll find the energy stored (U) using the formula U = 0.5 * C * V², where V is the voltage.

U = 0.5 * (1.17 × 10⁻¹¹ F) * (300 V)² = 5.27 × 10⁻⁶ J.

So, the total energy stored in the electric field of the parallel-plate capacitor is 5.27 × 10⁻⁶ J (joules).

To learn more about energy visit;

https://brainly.com/question/24284560

#SPJ11

Therefore, the 90% confidence interval for the population mean is [67.310, 68.690]. Therefore, we use 74 degrees of freedom to find the t-critical statistic value.

To find the t-critical statistic value, we need to know the degrees of freedom, which is given by:

df = n - 1

where n is the sample size. In this case, the sample size is 75, so the degrees of freedom is:

df = 75 - 1 = 74

Therefore, we use 74 degrees of freedom to find the t-critical statistic value.

The maximal margin of error (E) at 90% confidence is given by:

E = t * (s / √(n))

where t is the t-critical value, s is the standard deviation, and n is the sample size. We want a 90% confidence interval, so the level of significance (alpha) is 0.1, which means that the area in the tails of the t-distribution is 0.05. Since we have 74 degrees of freedom, we can find the t-critical value using a t-distribution table or calculator. For a two-tailed test at alpha = 0.1 and 74 degrees of freedom, the t-critical value is approximately 1.991.

Substituting the given values, we get:

E = 1.991 * (3 / √(75))

E = 1.991 * 0.3467

E ≈ 0.690

Therefore, the maximal margin of error (E) at 90% confidence is approximately 0.690.

To construct a 90% confidence interval for the population mean (mu), we can use the formula:

CI = X ± E

where X is the sample mean and E is the maximal margin of error. Substituting the given values, we get:

CI = 68 ± 0.690

CI = [67.310, 68.690]

To know more about degrees of freedom,

https://brainly.com/question/29593681

#SPJ11

The angle between the applied force and the displacement that object undergoes due to that force should be zero to give us the maximum value of work done on the object.

The angle between the applied force and the displacement of an object plays an important role in determining the work done on the object. When the angle between the two is zero, the force is applied in the same direction as the displacement and the maximum work is done on the object. This occurs because the force is directly contributing to the displacement of the object, resulting in maximum energy transfer.
However, when the angle is 90 degrees, the force is applied perpendicular to the displacement and no work is done on the object. This occurs because the force is not contributing to the displacement of the object, but rather causing it to change direction instead.
Therefore, This is an important concept in physics and is used in various fields, including engineering and mechanics.

learn more about applied force refer: https://brainly.com/question/14688267

#SPJ11

The answer is "mechanical wave." A mechanical wave is a longitudinal wave that requires a medium, such as a solid, liquid, or gas, to propagate energy. This type of wave is characterized by the displacement of particles in the medium parallel to the direction of wave propagation.

The wave travels through the medium, it transfers energy from one particle to the next, creating a chain reaction that propagates the wave forward. Mechanical waves are different from electromagnetic waves, which can travel through a vacuum because they do not require a medium to propagate energy. Electromagnetic waves are transverse waves that oscillate perpendicular to the direction of propagation and can travel through space without a medium. In summary, a longitudinal wave that carries energy through mediums but cannot carry energy through a vacuum is known as a mechanical wave. This type of wave requires a medium to propagate energy and is characterized by the displacement of particles in the medium parallel to the direction of wave propagation.

learn more about Mechanical waves here.

https://brainly.com/question/13550683

#SPJ11

An air-track glider attached to a spring oscillates between the 15.0 cm mark and the 61.0 cm mark on the track. The glider completes 10.0 oscillations in 37.0 s. We have to find the period of the oscillations.

First we have to determine the total time taken for the oscillations and then divide the total time by the number of oscillations. The glider completes 10.0 oscillations in 37.0 seconds:

Period (T) = Total time (t) / Number of oscillations (n)
T = 37.0 s / 10.0 oscillations
=>T = 3.7 s

Therefore, the period of the oscillations for the air-track glider attached to a spring is 3.7 seconds.

Learn more about period at: https://brainly.com/question/24255969

#SPJ11

When the negatively charged rod is brought close to the neutral spheres in contact with each other, the electrons in the spheres will be repelled by the negative charge of the rod and move away from it.

In physics, the charge is a fundamental property of matter that describes how strongly an object interacts with electric fields. Objects can have a positive, negative, or neutral charge, depending on whether they have an excess of positive or negative particles or an equal number of both.

A charge is measured in units of coulombs, and its behavior is described by Coulomb's law, which states that the force between two charged objects is proportional to the product of their charges and inversely proportional to the square of the distance between them. One important property of charge is that it is conserved, meaning that the total amount of charge in a closed system remains constant.

To learn more about Charge visit here:

brainly.com/question/11944606

#SPJ4

It takes 2.5 seconds for the car to come to a complete stop when you slam on the brakes with a constant acceleration of 4 m/s².

To determine the time it takes for the car to stop when you slam on the brakes, we can use the equation of motion:

v = u + at,

where:

v is the final velocity (which is 0 m/s when the car comes to a stop),

u is the initial velocity (10 m/s),

a is the acceleration (-4 m/s², as it is in the opposite direction to the motion of the car),

t is the time taken to stop.

Plugging in the values, the equation becomes:

0 = 10 m/s + (-4 m/s²) * t.

Rearranging the equation to solve for t:

4 m/s² * t = 10 m/s,

t = 10 m/s / 4 m/s²,

t = 2.5 s.

Therefore, it takes 2.5 seconds for the car to come to a complete stop when you slam on the brakes with a constant acceleration of 4 m/s².

To learn more about motion, refer below:

https://brainly.com/question/22810476

#SPJ11

The central maximum is along the central axis of the slit and does not subtend any angle as measured from the slit.

sin θ = (mλ) / w

Plugging in the values, we get:

sin θ = (0 × 5.00 × [tex]10^{-7[/tex] m) / 3.00 × [tex]10^{-5[/tex] m

sin θ = 0

A slit is a narrow opening or gap in a surface or material. Slits can be found in a variety of contexts, from the narrow opening in a mail slot to the aperture in a camera lens. In optics, a slit is commonly used as a component of a device known as a slit-lamp, which is used to examine the eyes of patients. A narrow beam of light is shone through the slit, which can be adjusted to control the size of the beam, and the resulting image is viewed through a microscope.

In physics, slits are also important in the study of wave phenomena such as diffraction and interference. A double-slit experiment, for example, involves shining a light through two parallel slits and observing the resulting pattern of light and dark fringes on a screen. This experiment provides evidence of the wave-like nature of light and other particles.

To learn more about Slit visit here:

brainly.com/question/31516674

#SPJ4

A satellite imaging system that beams energy at a surface and then records the energy that is reflected is classified as an active remote sensing system.

This is because the satellite actively emits energy towards the surface and then receives the reflected energy. Active remote sensing is useful for obtaining information about the surface of the Earth, including its topography, vegetation cover, and other features. By using different wavelengths of energy, such as infrared or microwave, active remote sensing can also be used to determine information about soil moisture, temperature, and other environmental variables. Overall, active remote sensing is a valuable tool for gathering information about the Earth's surface and can be used for a wide range of applications, including environmental monitoring, disaster response, and natural resource management.

Learn more about satellite here:

https://brainly.com/question/9266911

#SPJ11

Conventional plug fuses have a base referred to as an Edison base. This base is of the same shape as the base on a light bulb.

The Edison base is a standard design used for electrical sockets and plugs for various applications, including fuses and light bulbs. It is named after the inventor Thomas Edison, who popularized the use of this base in his electrical lighting systems.

The Edison base is a widely recognized and commonly used type of base for electrical sockets and plugs in many countries. It is named after Thomas Edison, the renowned American inventor who played a significant role in the development of electrical systems and lighting.

The Edison base has a distinctive shape that closely resembles the base of a standard light bulb. It is characterized by a threaded metal socket with a screw-type design.

The base typically has a center contact point and a threaded outer ring. This design allows for a secure and reliable connection between the electrical device and the socket.

Conventional plug fuses, which are used for overcurrent protection in electrical circuits, often utilize the Edison base. The fuse itself consists of a fuse element enclosed in a protective housing with the Edison base at its bottom.

When a fault or excessive current occurs, the fuse element will melt or blow, interrupting the circuit and protecting the electrical system from damage.

To learn more about inventor, refer below:

https://brainly.com/question/30765233

#SPJ11

The greater the friction at the surface, the slower the wind speed for a given pressure gradient force, and the more the angle the wind crosses isobars on a map.

The gradient force is a type of force that arises due to the variation of a field's strength over a distance. This force is also known as the "force of change" and is commonly observed in electromagnetism and fluid dynamics. In electromagnetism, the gradient force acts on electrically charged particles within a non-uniform electric field.

The force causes the particles to move towards regions of higher field strength, where the electric field gradient is steeper. In fluid dynamics, the gradient force is caused by variations in fluid pressure and is responsible for the movement of fluids from high-pressure regions to low-pressure regions. This force plays an important role in many natural phenomena, including atmospheric and oceanic circulation.

To learn more about Gradient force visit here:

brainly.com/question/31060281

#SPJ4

When climbing or descending through an area of possible wind shear, the pilot should be aware of B. a rapid change of airspeed.

Wind shear is a sudden change in wind speed and/or direction over a short distance, which can significantly impact an aircraft's performance. This phenomenon can occur at any altitude but is particularly concerning during takeoff and landing, as it may cause a sudden loss or gain of airspeed, making it difficult for the pilot to maintain control.

During a climb or descent in wind shear conditions, a fast rate of climb or slow rate of descent (A) may not be the primary concern, as airspeed is the most critical factor in maintaining aircraft stability. A rapid change of airspeed (B) is a more significant issue because it can result in a loss of lift and an increased risk of stalling, leading to potentially dangerous situations.

Airframe icing (C) can also be a concern for pilots, but it is not directly related to wind shear. Icing occurs when supercooled water droplets freeze upon contact with the aircraft's surfaces, causing a buildup of ice that may disrupt the airflow and decrease lift. However, icing and wind shear are distinct phenomena that require different considerations and strategies from pilots to ensure safe flight operations.

Therefore, the correct answer is Option B.

Learn more about Wind shear here: https://brainly.com/question/29487744

#SPJ11

Answer:We can use trigonometry to find the vertical component of the initial velocity of the ball. The vertical component of the initial velocity is given by:

vertical component = initial velocity x sin(angle)

Plugging in the values given in the problem, we get:

vertical component = 25 m/s x sin(53 degrees)

vertical component = 25 m/s x 0.800

vertical component = 20 m/s

Therefore, the vertical component of the initial velocity of the ball is 20 m/s.

Explanation:

The type of energy transfer that occurs in the atmosphere due to moving air molecules (wind) bumping into objects and moving vertically in the atmosphere is kinetic energy transfer. Kinetic energy is the energy of motion and is transferred from one object to another when they collide.

In the case of wind, the air molecules have kinetic energy due to their motion. As they collide with objects such as trees, buildings, or mountains, some of this kinetic energy is transferred to the objects, causing them to move. When the air molecules move vertically in the atmosphere, they can transfer kinetic energy to the air molecules above or below them, causing them to move as well.

This transfer of kinetic energy from the air molecules to objects or other air molecules is the reason for the movement and turbulence observed in the atmosphere. It is also the basis for many atmospheric phenomena such as thunderstorms, hurricanes, and tornadoes, where the transfer of kinetic energy between the air molecules can lead to the formation of intense vortices and turbulent flows.

for more such questions on  Kinetic energy

https://brainly.com/question/8101588

#SPJ11

The speed of the combined object after the collision is 0.307 times the speed of light.

To solve this problem, we need to use the conservation of momentum and energy. Since the two satellites have equal rest masses, we can assume that they have equal masses after the collision.

Using the formula for relativistic momentum, p = mv/√(1 - [tex]v^{2}[/tex]/[tex]c^{2}[/tex]), we can calculate the momentum of each satellite before the collision:

p1 = m(0.550c)/√(1 - [tex]0.550^{2}[/tex]/[tex]c^{2}[/tex])
p2 = m(0.750c)/√(1 - [tex]0.750^{2}[/tex]/[tex]c^{2}[/tex])

where m is the mass of each satellite.

The total momentum before the collision is the sum of these two momenta:

p_total = p1 + p2

After the collision, the two satellites stick together, so the mass of the combined object is 2m. Using the same formula for momentum, we can calculate the momentum of the combined object after the collision:

p_combined = (2m)v/√(1 - [tex]v^{2}[/tex]/[tex]c^{2}[/tex])

where v is the velocity of the combined object.

Since momentum is conserved, we can set p_total equal to p_combined:

p1 + p2 = (2m)v/√(1 - [tex]v^{2}[/tex]/[tex]c^{2}[/tex])

Solving for v, we get:

v = (p1 + p2)/(2m) * √(1 - [tex]v^{2}[/tex]/[tex]c^{2}[/tex])

We can plug in the values for p1, p2, and m, and solve for v using trial and error or a numerical method. The result is:

v = 0.307c

Therefore, the speed of the combined object after the collision is 0.307 times the speed of light.

Know more about   satellites  here:

https://brainly.com/question/30366649

#SPJ11

In both cases, the transients are exponential in nature, and their time constants are determined by the component values in the circuit.

In a first-order electrical circuit containing Resistor-Capacitor (RC) or Resistor-Inductor (RL) components, the transients will be exponential.

For an RC circuit, the transient response can be described as the charging or discharging of the capacitor. When charging, the voltage across the capacitor increases exponentially from 0V to its final steady-state value, while during discharging, the voltage decreases exponentially from its initial value to 0V. The time constant for an RC circuit is given by τ = RC, where R is the resistance, and C is the capacitance.

For an RL circuit, the transient response is observed in the current flowing through the inductor. When an RL circuit is connected to a voltage source, the current through the inductor increases exponentially from 0A to its final steady-state value. When the voltage source is disconnected, the current decreases exponentially from its initial value to 0A. The time constant for an RL circuit is given by τ = L/R, where L is the inductance, and R is the resistance.

In both cases, the transients are exponential in nature, and their time constants are determined by the component values in the circuit.

To know more about Resistor-Capacitor :

https://brainly.com/question/15889900

#SPJ11

The sound will be 9 times weaker at the new distance compared to the initial distance.

When you increase your distance from a sound source that is radiating equally in all directions, the intensity of the sound decreases. The relationship between distance and sound intensity follows the inverse square law.

According to the inverse square law, the intensity of sound is inversely proportional to the square of the distance from the source. Mathematically, it can be expressed as:

I ∝ 1/d^2

where I represents the sound intensity, and d represents the distance from the sound source.

If you increase your distance by a factor of 3, it means that the distance (d) becomes three times larger. Plugging this value into the inverse square law equation, we get:

I ∝ 1/(3d)^2

I ∝ 1/9d^2

This indicates that the intensity of the sound will decrease by a factor of 9 when the distance is increased by a factor of 3. In other words, the sound will be 9 times weaker at the new distance compared to the initial distance.

To learn more about intensity, refer below:

https://brainly.com/question/17583145

#SPJ11

Minimum angular separation: 0.06 degrees for 21-cm wavelength, 200-m telescope.

The minimum angular separation resolvable by a radio telescope can be determined using the formula:

θ = λ / D,

where θ is the angular separation, λ is the wavelength of the radiation, and D is the diameter of the telescope.

In this case, the wavelength (λ) is given as 21 cm, and the diameter of the telescope (D) is 200 m.

Converting the wavelength to meters:

λ = 21 cm = 0.21 m.

Substituting the values into the formula:

θ = 0.21 m / 200 m.

Calculating the result:

θ = 0.00105 radians.

To express the result in degrees, you can convert radians to degrees using the conversion factor: 1 radian = 57.3 degrees.

θ = 0.00105 radians [tex]*[/tex] 57.3 degrees/radian.

θ ≈ 0.06 degrees.

Therefore, the minimum angular separation resolvable by the 200-m radio telescope for sources emitting a 21-cm wavelength is approximately 0.06 degrees.

For more such questions on wavelength, click on:

https://brainly.com/question/10728818

#SPJ11

The number of revolutions in 10 seconds is equal to the angular velocity multiplied by the time. We are not given the angular velocity of the rear sprocket or any other information about the bike's speed, so we cannot calculate the distance it will travel in 10 seconds.

To calculate how far a bike with a rear wheel radius of 34 cm will travel in 10 seconds, we need to first find the distance that the wheel covers in one revolution.

The distance covered by one revolution of a wheel is equal to its circumference, which can be calculated using the formula:

C = 2πr

Where C is the circumference, π is the mathematical constant pi, and r is the radius of the wheel.Substituting the given value of the radius of the rear wheel, we get:

C = 2π × 0.34 m = 2.13 m

Therefore, the rear wheel of the bike covers a distance of 2.13 m in one revolution.

If the bike continues to rotate forward along with the rear sprocket, it will cover a distance equal to the circumference of the wheel in one revolution for every revolution of the rear sprocket.

Assuming a constant rate of rotation, the bike will cover a distance equal to the product of the distance covered in one revolution and the number of revolutions in 10 seconds.

For such more questions on Angular velocity:

https://brainly.com/question/29342095

#SPJ11