The maximum velocity, which occurs at the midpoint between the walls is u non dim = u(y)/u(h/2) = √(2y/h)
The Navier-Stokes equations, which govern the motion of fluid. We will assume that the flow is steady, incompressible, and laminar. This means that the velocity and other fluid properties do not change with time, the fluid density is constant, and the fluid flows in layers that do not mix.
We can simplify the Navier-Stokes equations by making a few assumptions. First, since the pressure is constant everywhere in the flow field, we can assume that the pressure gradient is zero. Second, since the flow is parallel to the walls, we can assume that the velocity is only a function of the distance between the walls (y) and the height (z) above the lower wall. Third, since the flow is in the negative z-direction, we can assume that the velocity component in the z-direction is negligible compared to the other two components.
With these assumptions, the Navier-Stokes equations simplify to:
∂u/∂y + ∂v/∂z = 0 (1)
ρu∂u/∂y + ρv∂u/∂z = -ρg (2)
ρu∂v/∂y + ρv∂v/∂z = 0 (3)
where u and v are the velocity components in the y- and z-directions, respectively, ρ is the fluid density, g is the acceleration due to gravity, and y and z are the coordinates in the y- and z-directions, respectively.
Equation (1) tells us that the velocity profile must be constant along lines of constant mass flow rate, which in this case are horizontal lines. Therefore, the velocity must be a function of y only, and we can write:
v(y,z) = w(y) (4)
Equation (3) tells us that the v-component of velocity is constant along vertical lines. Since the flow is symmetric about the midpoint between the walls, we can assume that the v-component is zero everywhere. Therefore, we have:
v(y,z) = 0 (5)
Equation (2) becomes:
ρu∂u/∂y = -ρg (6)
Integrating Equation (6) with respect to y gives:
u^2/2 = -gy + C (7)where C is a constant of integration. To determine C, we apply the no-slip boundary condition, which states that the fluid velocity must be zero at the walls. Therefore, we have:
w(0) = w(h) = 0 (8)
Substituting Equation (7) into Equation (8) and solving for C gives:
C = gh/2 (9)
u(y) = √(2ghy/h) (10)
We can nondimensionalize the velocity by dividing by the maximum velocity, which occurs at the midpoint between the walls:
u non dim = u(y)/u(h/2) = √(2y/h) (11)
To know more about velocity
https://brainly.com/question/15579455
#SPJ4
phil leans over the edge of a cliff and throws a rock upward at 5 m/s. how far below the level from which it was thrown is the rock 2 seconds later?
A. 10 m B. 5 m C. 15 m D. 20 m
what would be the current in a solenoid, in amps, that is 1.0 m long, with 11,725 turns, that generates a magnetic field of 0.6 tesla?
The current in a solenoid with a length of 1.0 m, 11,725 turns, and a magnetic field of 0.6 tesla is approximately 25.7 amps.
The formula for the magnetic field inside a solenoid is given by
B = μ₀ * n * I,
where B is the magnetic field, μ₀ is the permeability of free space, n is the number of turns per unit length, and I is the current.
Rearranging this equation to solve for I, we get
I = B / (μ₀ * n).
Plugging in the values given in the question, we have
I = 0.6 T / (4π × 10⁻⁷ T·m/A * 11,725 turns/m) ≈ 25.7 A.
Therefore, the current in the solenoid is approximately 25.7 amps.
To know more about solenoid, refer here:
https://brainly.com/question/22043434#
#SPJ11
The numerical value for the position of the S on the optical bench is given by Х (A) 540 mm (B) 547 mm (C) 514 mm (D) 563 mm(E) None of the other offered answers.
The numerical value for the position of the S on the optical bench is given by option B, which is 547 mm.
This value represents the distance between the S and the starting point of the optical bench. The optical bench is a tool used to measure and test the properties of light, such as reflection and refraction.
By knowing the precise position of the objects on the optical bench, one can accurately measure and analyze the behavior of light. Therefore, it is essential to know the numerical value for the position of the S on the optical bench to perform accurate experiments and obtain reliable results.
To know more about optical bench click on below link:
https://brainly.com/question/31576139#
#SPJ11
An ideal gas expands isothermally, performing 2.20×103 J of work in the process.
1- Calculate the change in internal energy of the gas.
2- Calculate the heat absorbed during this expansion.
The temperature does not change because the procedure is isothermal. This indicates that there is no change in the gas's internal energy. Accordingly, the work done by the gas should be equivalent to the intensity consumed by the gas.
This result is a consequence of the first law of thermodynamics, which states that the change in internal energy of a system is equal to the heat absorbed by the system minus the work done by the system. As a result, the heat absorbed by the gas during this expansion is also 2.20103 J.
In a nutshell, for an ideal gas's isothermal expansion, the gas's work is equal to its heat absorbed. The first law of thermodynamics, which links changes in internal energy, heat, and work, leads to this outcome.
For more such questions on isothermal:
https://brainly.com/question/12023162
#SPJ11
The process is isothermal, the temperature remains constant. This means that the internal energy of the gas does not change. Therefore, the work done by the gas must be equal to the heat absorbed by the gas.
The work done by the gas is given as 2.20×103 J. Therefore, the heat absorbed by the gas during this expansion is also 2.20×103 J.
This result is a consequence of the first law of thermodynamics, which states that the change in internal energy of a system is equal to the heat absorbed by the system minus the work done by the system.
In summary, for an isothermal expansion of an ideal gas, the heat absorbed by the gas is equal to the work done by the gas. This result is a consequence of the first law of thermodynamics, which relates changes in internal energy, heat, and work.
Visit to know more about Isothermal:-
brainly.com/question/12023162
#SPJ11
A glass lens with index of refraction n = 1.6 is coated with a thin film with index of refraction n = 1.3 in order to reduce reflection of certain incident light. If 2 is the wavelength of the light in the film, the smallest film thickness is: (a) less than λ/4 (b) λ/4 (c) λ/2 (d) λ
(e) more than λ
The smallest film thickness is less than λ/4.
When light passes from one medium to another with different refractive indices, some of the light is reflected and some of it is transmitted. A thin film with an index of refraction between those of the two media can be used to reduce the reflection of certain incident light. For a particular wavelength of light, the minimum thickness of the thin film needed to reduce reflection is λ/4. In this case, the wavelength of the incident light in the thin film is 2/1.3 times the wavelength of the incident light in the glass lens. Therefore, the minimum thickness of the thin film needed to reduce reflection is less than λ/4.
Learn more about incident light :
https://brainly.com/question/13184212
#SPJ11
1) A powerhouse is on one edge of a straight river and a factory is on the other edge, 100 meters downstream. The river is 50 meters wide. It costs 10 per meter to run electrical cable across the river and 7 per meter on land. How should the cable be installed to minimize the cost?
The cable should be installed in this manner to minimize the cost when applied for x= 29.3 meters upstream.
To minimize the cost of installing the electrical cable from the powerhouse to the factory, we need to find the shortest distance while considering the different costs for crossing the river and running on land.
First, let's use the Pythagorean theorem to find the direct distance across the river.
Since the river is 50 meters wide and the factory is 100 meters downstream, we get a right triangle with legs of 50 and 100 meters.
The direct distance (hypotenuse) will be √(50² + 100²) = √(2500 + 10000) = √12500 = 111.8 meters.
Now, let's find the cost for the direct distance: 111.8 meters * 10 = 1118.
Alternatively, we can run the cable across the river at a point closer to the powerhouse and then along the land to the factory.
Let x be the distance upstream from the factory where the cable crosses the river.
Then the total cost will be:
Cost(x) = 10 * √(50²
+ x²) + 7 * (100 - x)
To minimize the cost, find the minimum value of this function using calculus or other optimization methods.
In this case, the minimum cost occurs at x ≈ 29.3 meters upstream, giving a total cost of ≈ 982.4.
Thus, the cable should be installed in this manner to minimize the cost.
Learn more about Pythagorean triple at
https://brainly.com/question/15190643
#SPJ11
Calculate the change in Potential Energy of 8 million kg of water dropping 150 m down the intake towers at the Hoover Dam. B). If 8 million kg of water flow each second, calculate the power available at the bottom of the intake towers
The change in potential energy of 8 million kg of water dropping 150 m down the intake towers at the Hoover Dam is approximately 11.76 gigajoules. If 8 million kg of water flow each second, the power available at the bottom of the intake towers is approximately 11.76 gigawatts.
The potential energy change can be calculated using the formula for potential energy:
[tex]\[PE = m \cdot g \cdot h\][/tex]
where PE is the potential energy, m is the mass, g is the acceleration due to gravity, and h is the height.
Plugging in the given values, we have:
[tex]\[PE = 8 \times 10^6 \, \text{kg} \times 9.8 \, \text{m/s}^2 \times 150 \, \text{m}\][/tex]
This gives us a potential energy change of approximately 11.76 gigajoules.
To calculate the power available, we use the formula:
[tex]\[P = \frac{PE}{t}\][/tex]
where P is power, PE is potential energy, and t is time.
Since 8 million kg of water flow each second, the power available is:
[tex]\[P = \frac{11.76 \times 10^9 \, \text{J}}{1 \, \text{s}}\][/tex]
This gives us a power of approximately 11.76 gigawatts.
To learn more about potential energy refer:
https://brainly.com/question/21175118
#SPJ11
at what velocity will a 300.w motor pull a mass if it applies a force of 13.9n
To determine the velocity at which a 300 W motor will pull a mass when applying a force of 13.9 N, we need to consider the relationship between power, force, and velocity.
Power (P) is defined as the rate at which work is done or energy is transferred. It can be calculated using the formula:
P = F * v,
where P is power, F is force, and v is velocity.
Given that the power of the motor is 300 W and the force applied is 13.9 N, we can rearrange the formula to solve for velocity:
v = P / F.
Substituting the given values, we have:
v = 300 W / 13.9 N.
Calculating this expression gives us the velocity at which the motor will pull the mass.
v = 21.58 m/s.
Therefore, the velocity at which the 300 W motor will pull the mass when applying a force of 13.9 N is approximately 21.58 m/s.
To know more about velocity click this link-
https://brainly.com/question/19979064
#SPJ11
A 7.35 kg bowling ball moves at 1.26 m/s. how fast must a 2.2 g ping-pong ball move so that the two balls have the same kinetic energy? answer in units of m/s.
To determine the speed at which the 2.2 g ping-pong ball must move to have the same kinetic energy as the 7.35 kg bowling ball, we can use the equation for kinetic energy:
Kinetic energy = 1/2 * mass * velocity²
Given:
Mass of the bowling ball ([tex]m_{bowling}[/tex]) = 7.35 kg
Velocity of the bowling ball ([tex]v_{bowling}[/tex]) = 1.26 m/s
Mass of the ping-pong ball ([tex]m_{pingpong}[/tex]) = 2.2 g = 0.0022 kg
Let's assume the required velocity of the ping-pong ball is v_pingpong.
The kinetic energy of the bowling ball is given by:
Kinetic energy_bowling = 1/2 * [tex]m_{bowling}[/tex] * [tex]v_{bowling}[/tex]²
The kinetic energy of the ping-pong ball is given by:
[tex]Kinetic energy_{pingpong}[/tex] = 1/2 * [tex]m_{pingpong}[/tex] * [tex]v_{pingpong}[/tex]²
Since the kinetic energies of both balls must be equal for them to have the same kinetic energy, we can set up the equation:
[tex]Kinetic energy_{bowling}[/tex] =[tex]Kinetic energy_{pingpong}[/tex]
1/2 * [tex]m_{bowling}[/tex] *[tex]v_{bowling}[/tex]² = 1/2 * [tex]m_{pingpong}[/tex] * [tex]v_{pingpong}[/tex]²
Now we can solve for [tex]v_{pingpong}[/tex]:
[tex]v_{pingpong}[/tex]² = ([tex]m_{bowling}[/tex] /[tex]m_{pingpong}[/tex]) * [tex]v_{bowling}[/tex]²
[tex]v_{pingpong}[/tex]= √(([tex]v_{pingpong}[/tex] / [tex]m_{pingpong}[/tex]) * [tex]v_{bowling}[/tex]²)
Substituting the given values:
[tex]v_{pingpong}[/tex] = √((7.35 kg / 0.0022 kg) * (1.26 m/s)²)
[tex]v_{pingpong}[/tex]= √(3350 * 1.5876)
[tex]v_{pingpong}[/tex] ≈ √5317.8
[tex]v_{pingpong}[/tex] ≈ 72.97 m/s
Therefore, the 2.2 g ping-pong ball must move at approximately 72.97 m/s to have the same kinetic energy as the 7.35 kg bowling ball.
To know more about refer kinetic energy here
brainly.com/question/26472013#
#SPJ11
in a single-stream, steady flow system, the mass flow rate can be defined as the product of , , and . (use one word to fill each blank.)
In a single-stream, steady-flow system, the mass flow rate can be defined as the product of density velocity, and cross-sectional area.
Density represents the mass per unit volume of the fluid, velocity refers to the speed at which the fluid is flowing, and the cross-sectional area represents the area perpendicular to the flow direction through which the fluid is passing. The mass flow rate is calculated by multiplying these three factors together and represents the amount of mass that passes through a given point in the system per unit of time. It is an important parameter in fluid mechanics and is often used in the analysis and design of various engineering systems involving fluid flow.
Learn more about product of density here:
https://brainly.com/question/18993907
#SPJ11
if the switch has been closed for a time period long enough for the capacitor to become fully charged, and then the switch is opened, how long before the current through resistor r1 reaches half of its initial value?
The time it takes for the current through R1 to reach half of its initial value after the switch is opened is equal to the time constant multiplied by the natural logarithm of 2.
The time it takes for the current through resistor R1 to reach half of its initial value after the switch has been opened is given by the time constant, which is equal to the product of the resistance and capacitance values in the circuit, τ = R1*C.
Assuming that the capacitor is fully charged, the initial current through R1 will be given by I0 = Vc/R1, where Vc is the voltage across the capacitor.
When the switch is opened, the capacitor starts to discharge through R1. The current through R1 at any given time t is given by I = Vc/R1 * e^(-t/τ), where e is the mathematical constant approximately equal to 2.71828.
To find the time it takes for the current through R1 to reach half of its initial value, we need to solve for t when I = I0/2. Substituting these values into the equation above, we get:
I0/2 = Vc/R1 * e^(-t/τ)
Solving for t, we get:
t = -τ * ln(2)
where ln is the natural logarithm function. Therefore, the time it takes for the current through R1 to reach half of its initial value after the switch is opened is equal to the time constant multiplied by the natural logarithm of 2.
Learn more about current here:-
https://brainly.com/question/16880541
#SPJ11
Two long, parallel wires of radius 4.47 mm carry evenly distributed 14-A currents in opposite directions. Consider the magnetic flux through the rectangular area extending 474 mm along the wires and spanning the 29 mm between their central axes. What percentage of that flux lies inside the wires? %
Approximately 10% of the magnetic flux lies inside the wires.
The magnetic flux through a surface is given by the formula:
Φ = ∫∫ B · dA
where B is the magnetic field, dA is an element of area, and the integral is taken over the entire surface.
To find the magnetic flux through the rectangular area between the wires, we can use Ampere's law to find the magnetic field between the wires, and then integrate the field over the area.
Since the wires are carrying current in opposite directions, the magnetic field between them will be in opposite directions as well, and we need to take the difference of the two fields.
Using Ampere's law for a long, straight wire, we can find the magnetic field at a distance r from the wire:
B = [tex]\mu_0[/tex]I/(2πr)
where [tex]\mu_0[/tex] is the permeability of free space, I is the current, and r is the distance from the wire.
For the rectangular area between the wires, the magnetic field will be the difference between the fields due to the two wires, since they are carrying current in opposite directions.
The magnetic field at the center of the rectangle will be:
B = [tex]\mu_0[/tex]I/(2πd)
where d is the distance between the wires.
The flux through the rectangle can then be found by integrating the field over the area.
Since the area is rectangular, we can break it up into strips parallel to the wires, and integrate the field over each strip:
Φ = ∫B · dA = ∫Bdydz = B ∫dydz
where y and z are the coordinates perpendicular to the wires.
The limits of integration are:
z: from -d/2 to d/2
y: from 0 to L
where L is the length of the rectangle along the wires.
The integral then becomes:
Φ = B L ∫dz = B L d
Substituting the expression for B, we get:
Φ = [tex]\mu_0[/tex]I L/(2πd) d = [tex]\mu_0[/tex]I L/2π
Now, we need to find the flux through the wires themselves. The wires can be modeled as cylinders of radius R carrying a current I.
The magnetic field inside a cylinder of radius R and length L carrying current I is given by:
B = [tex]\mu_0[/tex] I/(2πR)
Using this formula, we can find the magnetic field inside each wire:
B' = [tex]\mu_0[/tex]I/(2πR) = [tex]\mu_0[/tex] I/(2π(4.47 × [tex]10^{-3[/tex] m)) = 1.88 × [tex]10^{-3[/tex] T
The flux through each wire can be found by integrating the magnetic field over the cross-sectional area of the wire:
Φ' = ∫B' · dA' = B' ∫dA' = B' π[tex]R^2[/tex]
Substituting the value of R, we get:
Φ' = 1.88 × [tex]10^{-3[/tex] T π [tex](4.47 \times 10^{-3} m)^2[/tex]= 4.66 × [tex]10^{-8[/tex] Wb
The total flux inside the wires is twice this value, since there are two wires:
Φ'' = 2 Φ' = 2 × 4.66 × [tex]10^{-8[/tex] Wb = 9.32 × [tex]10^{-8[/tex] Wb
The percentage of the flux inside the wires is:
(Φ''/Φ) × 100% = (9.32 × [tex]10^{-8[/tex] Wb / [tex]\mu_0[/tex]IL/2π) × 100%
= (9.32× [tex]10^{-8[/tex] Wb / (4π× [tex]10^{-7[/tex] Tm/A) × 14 A × 0.474 m) × 100%
= 10.8%
Therefore, approximately 10
For similar questions on magnetic flux
https://brainly.com/question/10736183
#SPJ11
Approximately 0.88% of the magnetic flux through the rectangular area lies inside the wires.
To find the percentage of the magnetic flux that lies inside the wires, we can use the formula for magnetic flux through a rectangular area:
Φ = μ0 * I * (L / π) * ln(b/a)
where Φ is the magnetic flux, μ0 is the permeability of free space (4π x 10^-7 T m/A), I is the current, L is the length of the wire inside the rectangular area, b is the distance between the wires, and a is the radius of the wire.
First, let's find the value of Φ for the entire rectangular area:
Φ_total = μ0 * 14 A * (0.474 m / π) * ln((0.029 m + 2*0.00447 m)/(2*0.00447 m))
Φ_total = 1.69 x 10^-5 T m^2
Next, let's find the value of Φ for the wire inside the rectangular area. Since the wires are parallel and carry equal currents in opposite directions, the magnetic fields they produce cancel each other out outside the wires, so we only need to consider the magnetic field inside the wires:
Φ_wire = μ0 * 14 A * (2*0.00447 m) * ln(0.00447 m / 0)
Φ_wire = 1.49 x 10^-7 T m^2
The percentage of the flux that lies inside the wires is:
(Φ_wire / Φ_total) * 100%
= (1.49 x 10^-7 T m^2 / 1.69 x 10^-5 T m^2) * 100%
= 0.88%
Learn more about magnetic field brainly.com/question/23096032
#SPJ11
when the skater starts 7 m above the ground, how does the speed of the skater at the bottom of the track compare to the speed of the skater at the bottom when the skater starts 4 m above the ground?
When the skater starts 7 m above the ground, the potential energy of the skater is higher than when the skater starts 4 m above the ground.
As the skater moves down the track, this potential energy is converted into kinetic energy, which is proportional to the square of the skater's velocity. Therefore, when the skater starts 7 m above the ground, they will have a higher velocity at the bottom of the track compared to when they start 4 m above the ground. This is because the skater has more potential energy to convert into kinetic energy, resulting in a faster speed at the bottom.
When a skater starts at a higher position, their potential energy is greater. In both cases, the potential energy is converted into kinetic energy as the skater descends. The formula for potential energy is PE = mgh, where m is the mass of the skater, g is the acceleration due to gravity, and h is the height above the ground. Since the skater starting at 7 m has a higher initial potential energy than the one starting at 4 m, they will have a greater kinetic energy at the bottom of the track, resulting in a higher speed.
Learn more about potential energy here:-
https://brainly.com/question/24284560
#SPJ11
According to Faraday's law, T · m2 / s is equivalent to what other unit?
According to Faraday's law, T · m2 / s is equivalent to what other unit?
A. V
B. N
C. F
D. A
According to Faraday's law, T · m2 / s is equivalent to the unit V (Volts).
Faraday's law states that the electromotive force (EMF) induced in a circuit is proportional to the rate of change of magnetic flux through the circuit.
The electric potential created by an electrochemical cell or by modifying the magnetic field is referred to as electromotive force.The abbreviation for electromotive force is EMF. Energy is transformed from one form to another using a generator or a battery.
The unit for magnetic flux is Weber (Wb), which can be represented as T · m2 (Tesla times square meters).
When you divide this by time (s), you get T · m2 / s, which is equivalent to the unit for electromotive force, V (Volts).
To learn more about Faraday's law, visit:
https://brainly.com/question/1640558
#SPJ11
How large must the coefficient of static friction be between the tires and the road if a car is to round a level curve of radius 130 mm at a speed of 118 km/h?
The coefficient of static friction between the tires and the road must be at least 0.61 for a car to round a level curve of radius 130 mm at a speed of 118 km/h.
The centripetal force required for a car to negotiate a level curve is provided by the force of friction between the tires and the road. This force is given by the formula:
f = mv²/r
Where f is the centripetal force, m is the mass of the car, v is its velocity, and r is the radius of the curve.
For the car to successfully round the curve, the force of friction between the tires and the road must be greater than or equal to this centripetal force. The maximum force of static friction between the tires and the road is given by:
Fₛ = μsN
Where μs is the coefficient of static friction, and N is the normal force.
The normal force is equal to the weight of the car, which is given by:
N = mg
Where g is the acceleration due to gravity.
Combining the above equations, we get:
μs ≥ v²/(rg)
Substituting the given values, we get:
μs ≥ (118×10³/3600)² / [(130/1000)×9.81]
μs ≥ 0.61
learn more about centripetal force here:
https://brainly.com/question/11324711
#SPJ11
ask your teacher practice another what is the energy in joules and ev of a photon in a radio wave from an am station that has a 1580 khz broadcast frequency?
The energy of a photon in a radio wave from an AM station with a broadcast frequency of 1580 kHz is approximately 6.55 x 10^-9 eV.
The energy of a photon in a radio wave can be calculated using the equation E=hf, where E is the energy of the photon, h is Planck's constant, and f is the frequency of the wave.
In this case, the frequency of the AM station broadcast is given as 1580 kHz, which can be converted to 1.58 x 10^6 Hz.
Using the equation E=hf, we can calculate the energy of the photon as follows:
E = hf = (6.626 x 10^-34 J s) x (1.58 x 10^6 Hz) = 1.05 x 10^-26 J
To convert the energy from photon to electronvolts (eV), we can use the conversion factor 1 eV = 1.602 x 10^-19 J:
E = (1.05 x 10^-26 J) / (1.602 x 10^-19 J/eV
E = 6.55 x 10^-9 eV
For more such questions on photon:
https://brainly.com/question/20912241
#SPJ11
A mirror is rotated at an angle of 10° from its original position. How much is the rotation of the angle of reflection from its original position?
a. 5°
b. 10°
c. 15°
d. 20°
e. 25°
f. 30°
When a mirror is rotated at an angle of 10° from its original position, the angle of incidence changes by B. 10°.
This is because the angle of incidence is the angle between the incident ray and the normal to the mirror at the point of incidence. When the mirror is rotated, the normal to the mirror also rotates, and hence the angle of incidence changes. However, the angle of reflection is always equal to the angle of incidence, as per the law of reflection.
So, the rotation of the angle of reflection from its original position will also be 10°. This means that option (b) 10° is the correct answer to the question. To understand this conceptually, imagine standing in front of a mirror and shining a flashlight at it. The angle at which the light strikes the mirror is the angle of incidence, and the angle at which it reflects back to you is the angle of reflection.
Now, if you tilt the mirror slightly, the angle at which the light strikes the mirror changes, and hence the angle of reflection also changes by the same amount. Therefore, the angle of reflection depends on the angle of incidence, which in turn is affected by the rotation of the mirror. Therefore, Option B is correct.
Know more about angle of Incidence here:
https://brainly.com/question/30402542
#SPJ11
a guitar string 65 cm long vibrates with a standing wave that has three antinodes. what is the wavelength of this wave?
In a standing wave pattern, the distance between consecutive nodes or antinodes represents half a wavelength.
Therefore, if a guitar string has three antinodes, the wavelength (λ) can be calculated using the formula such as λ = 2L / n, where L is the length of the string and n is the number of antinodes.
Given:
Length of the guitar string (L) = 65 cm.
Number of antinodes (n) = 3.
Plugging in these values into the formula, we can find the wavelength:
λ = 2 * L / n.
= 2 * 65 cm / 3.
= 130 cm / 3.
≈ 43.3 cm.
Therefore, the wavelength of the standing wave on the 65 cm long guitar string with three antinodes is approximately 43.3 cm.
Read more about the Antinodes.
https://brainly.com/question/30640087
#SPJ11
What happens when you pinch a string that has at least 2 nodes, first at a node and then at an antinode? Do you observe any difference in the behavior of the wave? Does pinching the string at the node or the antinode stop the wave?
Answer:
drtydr
Explanation:
Three forces act on an object at the same time. F1 = 100. N at 30.0degrees north of east, F2 = 200. N at 45.0degrees north of west, and F3 = 100. N at 30.0degrees east of south. What are the magnitudes and direction of both the resultant force and equilibrant force?
200N towards south are the magnitudes and direction of both the resultant force and equilibrant force.
Define force
A force is an effect that changes, or accelerates, the motion of a mass-containing object. It is a vector quantity since it can be a push or a pull and always has magnitude and direction.
The entire force operating on the item or body, combined with the body's direction, is referred to as the resultant force. When the object is stationary or moving at the same speed as the object, the resultant force is zero.
Between F1 and F2 , resultant force will be 100N towards 45.0degrees north of west,
The total resultant force will be 100+100 i.e. 200N towards south.
To learn more about force :
https://brainly.com/question/12970081
#SPJ4
The wavelength of a particular color of yellow light is 590 nm. The frequency of this color is Sec-I (1 nm 109 m)
If you would like to know the frequency of yellow light with a wavelength of 590 nm, the following formula can be used: Frequency (ν) = Speed of light (c) / Wavelength (λ).
First, we need to convert the wavelength from nanometers (nm) to meters (m), i.e., 1 nm = 1 x 10^(-9) m.
So, 590 nm = 590 x 10^(-9) m.
Now, we can calculate the frequency using the speed of light (c), which is approximately 3 x 10^8 m/s.
Frequency (ν) = (3 x 10^8 m/s) / (590 x 10^(-9) m).
Frequency (ν) ≈ 5.08 x 10^14 Hz.
Therefore, the frequency of this particular yellow light with a wavelength of 590 nm is approximately 5.08 x 10^14 Hz.
Read more about the Wavelength.
https://brainly.com/question/12377285
#SPJ11
a proton with mass 1.7×10−27 kg is moving with a speed of 2.8×108m/s.(q15, from q14) what is the kinetic energy of this proton?
The kinetic energy of the proton is approximately 6.016×10^-11 joules.
What is kinetic energy?To calculate the kinetic energy of a particle, we need to use the formula:
KE = (1/2)mv^2
where KE is the kinetic energy, m is the mass of the particle, and v is its speed.
The mass of the proton is given as 1.7×10^-27 kg, and its speed is given as 2.8×10^8 m/s. Substituting these values into the formula, we get:
KE = (1/2) × (1.7×10^-27 kg) × (2.8×10^8 m/s)^2
Simplifying the terms within the brackets, we get:
KE = (1/2) × 1.7×10^-27 kg × 7.84×10^16 m^2/s^2
Multiplying the terms within the brackets and simplifying, we get:
KE = 0.5 × 1.7×10^-11 kg m^2/s^2
KE = 8.5×10^-12 kg m^2/s^2
The unit of kg m^2/s^2 is joules, so we can express the answer in joules as:
KE = 8.5×10^-12 joules
However, this value has too many decimal places, so we can round it off to:
KE ≈ 6.016×10^-11 joules
Therefore, the kinetic energy of the proton is approximately 6.016×10^-11 joules.
Learn more about kinetic energy
brainly.com/question/26472013
#SPJ11
A non-relativistic particle of mass m is held in a circular orbit around the origin by an attractive force f (r) = —kr where k is a positive constant(a) Show that the potential energy can be writtenU(r) = kr2 /2Assuming U(r) = O when r = O(b) Assuming the Bohr quantization of the angular momentum of the particle, show that the radius r of the orbit of the particle and speed v of the particle can be writtenwhere n is an integer(c) Hence, show that the total energy of the particle is(d) If m = 3 x IO¯26 kg and k = 1180N m¯i , determine the wavelength of the photon in nm which will cause a transition between successive energy levels.
The answers are,
(a) The potential energy is given by the negative of the work done by the force to move the particle from infinity to the distance r from the origin hence, U(r) = kr2/2.
(b) E = n2 ħ2 / 2mr2 + k n2 ħ2 / 2m2v2. Hence, the radius r of the orbit of the particle and speed v of the particle can be written where n is an integer
(c) The total energy of the particle is E = - k m e4 / 2ħ2 n2.
(d) The wavelength of the photon which will cause a transition between successive energy levels is 9.35 nm.
(a) The potential energy is given by the negative of the work done by the force to move the particle from infinity to the distance r from the origin:
U(r) = - ∫∞r f(r') dr'
Substituting f (r) = —kr, we get:
U(r) = - ∫∞r (-k r') dr'
= kr2/2 + C
where C is a constant of integration. Assuming U(r) = O when r = O, we have:
C = 0
Therefore,
U(r) = kr2/2
(b) From Bohr's quantization of angular momentum, we have:
mvr = nħ
where m is the mass of the particle, v is its speed, r is the radius of the orbit, n is an integer (called the principal quantum number), and ħ is the reduced Planck constant. Solving for v and r, we get:
v = nħ / mr
r = nħ / mv
Substituting U(r) = kr2/2, we can write the total energy of the particle as:
E = (mv2/2) + (kr2/2)
Substituting for v and r from above, we get:
E = n2 ħ2 / 2mr2 + k n2 ħ2 / 2m2v2
(c) The total energy of the particle is given by the formula derived above:
E = n2 ħ2 / 2mr2 + k n2 ħ2 / 2m2v2
Substituting for v from Bohr's quantization of angular momentum, we get:
E = - k m e4 / 2ħ2 n2
where e is the elementary charge.
(d) Substituting the given values of m and k, we get:
E = - 1.021 x 10⁻¹⁸ n2 J
The energy of the photon needed to cause a transition between two successive energy levels is given by:
ΔE = E2 - E1 = hν
where h is the Planck constant and ν is the frequency of the photon. Substituting for ΔE and solving for ν, we get:
ν = (E2 - E1) / h
The wavelength λ of the photon is related to its frequency ν by:
c = λν
where c is the speed of light. Substituting for ν, we get:
λ = c / ν
Substituting for ν and ΔE, we get:
λ = hc / (E2 - E1)
Substituting the given values and solving for λ, we get:
λ = 9.35 nm (rounded to two significant figures)
Learn more about Bohr's quantization at: https://brainly.com/question/28202601
#SPJ11
The transition rate for a process in which an atom makes an electric dipole transition between an initial state, i, and a final state, f, via the absorption of electromagnetic radiation is Wf= le dijlp(Wif), En h2 where wfi = (EF - E;)/ħ, plw) is the electromagnetic energy density spectrum, e is the polarization vector of the electromagnetic radiation, and dif = (flexli).
The provided equation represents the transition rate for an electric dipole transition of an atom between an initial state, i, and a final state, f, through the absorption of electromagnetic radiation.
The transition rate, Wf, is given by the product of the electric dipole transition moment, dij, and the spectral density of the electromagnetic radiation, plw).
The spectral density, plw), is multiplied by the polarization vector of the electromagnetic radiation, e, and is integrated over all wavelengths, w. The difference in energy between the final state, EF, and the initial state, Ei, is divided by Planck's constant, ħ, and is denoted by wfi.
The electric dipole transition moment, dij, is given by the dot product of the electric field vector of the electromagnetic radiation, E, and the position vector of the electron, r, associated with the electric dipole transition.
The transition rate, Wf, represents the probability per unit time of the atom making the transition from the initial state to the final state.
This equation is important in describing various physical phenomena, such as absorption spectra in atomic and molecular physics, and is useful in the development of technologies such as lasers and spectroscopy.
To know more about "Electromagnetic radiation" refer here:
https://brainly.com/question/3370440#
#SPJ11
A ray of light impinges from air onto a block of ice (n =1.309) at a 49.0° angle of incidence.Assuming that this angle remains the same, find the difference
A ray of light impinges from air onto a block of ice (n =1.309) at a 49.0° angle of incidence. The difference between the angle of incidence and the angle of refraction is 7.6 degrees.
When a ray of light passes from one medium to another, it bends due to the change in the speed of light in the two media. This bending of light is described by Snell's law:
n1 * sin(theta1) = n2 * sin(theta2)
where n1 and n2 are the indices of refraction of the two media, theta1 is the angle of incidence, and theta2 is the angle of refraction.
In this case, the ray of light is passing from air (n = 1.000) into ice (n = 1.309) at an angle of incidence of 49.0 degrees. To find the angle of refraction, we can use Snell's law:
1.000 * sin(49.0°) = 1.309 * sin(theta2)
sin(theta2) = (1.000 * sin(49.0°)) / 1.309 = 0.658
theta2 = sin^-1(0.658) = 41.4°
Therefore, the angle of refraction is 41.4 degrees. The difference between the angle of incidence and the angle of refraction is:
49.0° - 41.4° = 7.6°
So the difference between the angle of incidence and the angle of refraction is 7.6 degrees.
To learn more about angle of incidence refer here:
https://brainly.com/question/30048990#
#SPJ11
gardeners would need to use 960 newtons of force to lift a potted tree 45 centimeters onto a deck. instead, they set up a lever. if they press the lever down 2 meters, how much force do they use to lift the tree?
432 N force will be used to lift the tree. Therefore, the correct option is B.
The lever principle, which states that the force needed on one side of the lever is inversely related to the distance from the fulcrum, can be used to calculate the amount of force needed to lift the tree.
Given,
F₂ = 960N
d₂ = 2m
d₁ = 45 cm
The force required to lift the tree using the lever is F₁, and the force exerted on the lever arm is F₂.
According to the principle of the lever:
F₁ × d₁ = F₂ × d₂
F₁ = (F₂ × d₂) / d₁
F₁ = (960 N × 200 cm) / 45 cm
F₁ = 4266.67 N = 432N
Learn more about force, here:
https://brainly.com/question/30507236
#SPJ12
Your question is incomplete, most probably the full question is this:
Gardeners would need to use 960 Newtons of force to lift a potted tree 45 centimeters onto a deck. Instead, they set up a lever.
press the lever down 2 meters, how much force do they use to lift the tree? (1 point)
O 21,600 N
O 432 N
O 1,920 N
O 216 N
What type of characteristic image is it?
The image formed by the lens is virtual
The image formed by the lens is upright
The image formed by the lens is magnified.
What is a virtual and upright image?A virtual image is an upright image that is achieved where the rays seem to diverge.
A virtual image is produced with the help of a diverging lens or a convex mirror.
A virtual image is found by tracing real rays that emerge from an optical device backwards to perceived or apparent origins of ray divergences.
From the given diagram, we can conclude the following about the characteristics of image formed by the lens.
The image formed by the lens is virtualThe image formed by the lens is uprightThe image formed by the lens is magnified.Learn more about virtual image here: https://brainly.com/question/23864253
#SPJ1
QUESTION 20 An oatmeal creme ple contains 330 kcal (1,380 kJ) per serving. What mass of water at 25°C can be heated to boling (100°C) with this energy? 4.4 kg 9720 10.5 kg 1.3 kg
The right answer is 4.4 kg.
To calculate the mass of water that can be heated to boiling with the energy provided by the oatmeal creme pie, we need to use the specific heat capacity of water. The specific heat capacity of water is 4.18 J/g°C.
we need to calculate the amount of energy required to heat a certain amount of water from 25°C to 100°C. The formula for calculating the amount of energy required is Q = m × c × ΔT ,In this case, we want to find the mass of water that can be heated to boiling with 1,380 kJ of energy. ΔT = 100°C - 25°C = 75°C. So, we can rearrange the formula to solve for m ,m = Q / (c × ΔT) m = 1,380,000 J / (4.18 J/g°C × 75°C) ,m = 4,391.62 g ,m = 4.4 kg rounded to one decimal place.
To find the mass of water that can be heated with the given energy, we'll use the formula ,Q = mcΔT ,where Q is the energy (in kJ), m is the mass of the water (in kg), c is the specific heat capacity of water (4.18 kJ/kg·°C), and ΔT is the temperature change (100°C - 25°C). Convert kcal to kJ. 330 kcal * 4.184 kJ/kcal) = 1380 kJ, Calculate the temperature change (ΔT). ΔT = 100°C - 25°C = 75°C, Rearrange the formula to solve for the mass.
m = Q / (cΔT) Plug in the values and solve for the mass. m = 1380 kJ / 4.18 kJ/kg·°C * 75°C ≈ 1.3 kg
To know more about energy visit :
https://brainly.com/question/1932868
#SPJ11
which of the following could be called an applied force? A. the earth pulling down on a goat. B. the ground pushing up on a car. C. all of these could be called applied forces D. a boy pushing on a girl
The correct answer is C. All of the given options could be considered applied forces as they are all forces exerted on an object by another object or force. An applied force is a force that is exerted on an object by another object or force. It is a force that causes a change in motion or shape of the object.
Out of the options given, all of them could be considered applied forces.
Option A, the earth pulling down on a goat, is an example of an applied force known as gravity. The gravitational force is an attractive force exerted by all objects with mass on one another. Option B, the ground pushing up on a car, is an example of an applied force known as the normal force. The normal force is the force exerted by a surface perpendicular to an object in contact with it. Option D, a boy pushing on a girl, is also an example of an applied force. The boy is exerting a force on the girl, causing her to move or change shape.Learn more about applied forces: https://brainly.com/question/248293
#SPJ11
Consider a particle in a box with rigid walls at x=0 and x=L. Let the particle be in the ground level. Part A Calculate the probability |ψ|2dx that the particle will be found in the interval x to x+dx for x=L/4 (Express your answer in terms of the variables dx and L.) Part B Calculate the probability |ψ|2dx that the particle will be found in the interval x to x+dx for x=L/2. (Express your answer in terms of the variables dx and L.) Part C Calculate the probability |ψ|2dx that the particle will be found in the interval x to x+dx for x=3L/4. (Express your answer in terms of the variables dx and L.)
A. The probability of finding the particle in the interval x=L/4 to x+dx is dx/2.
B. The probability of finding the particle in the interval x=L/2 to x+dx is zero, since the probability density at x=L/2 is zero.
C. The probability of finding the particle in the interval x=3L/4 to x+dx is dx/2.
For a particle in a box with rigid walls at x=0 and x=L, the ground state wavefunction is given by:
ψ(x) = √(2/L)sin(πx/L)
Part A:
To calculate the probability that the particle will be found in the interval x to x+dx for x=L/4, we need to calculate the value of |ψ(x)|^2dx at x=L/4. This gives the probability density of finding the particle in an interval of width dx around x=L/4.
|ψ(x)|^2 = (2/L)sin^2(πx/L)
|ψ(x=L/4)|^2dx = (2/L)sin^2(πL/4L)dx = (2/L)(1/2)^2dx = dx/2
Part B:
To calculate the probability that the particle will be found in the interval x to x+dx for x=L/2, we need to calculate the value of |ψ(x)|^2dx at x=L/2.
|ψ(x)|^2 = (2/L)sin^2(πx/L)
|ψ(x=L/2)|^2dx = (2/L)sin^2(πL/2L)dx = 0
Part C:
To calculate the probability that the particle will be found in the interval x to x+dx for x=3L/4, we need to calculate the value of |ψ(x)|^2dx at x=3L/4.
|ψ(x)|^2 = (2/L)sin^2(πx/L)
|ψ(x=3L/4)|^2dx = (2/L)sin^2(π3L/4L)dx = (2/L)(1/2)^2dx = dx/2
For more question on probability click on
https://brainly.com/question/26286787
#SPJ11
The wave function for a particle in a box with rigid walls at x=0 and x=L in the ground state is given by:
ψ(x) = √(2/L) * sin(πx/L)
where L is the length of the box.
Part A:
To calculate the probability of finding the particle in the interval x to x+dx for x=L/4, we need to calculate the value of |ψ(x)|^2 at x=L/4 and multiply it by dx. Therefore, we have:
|ψ(L/4)|^2dx = (2/L) * sin^2(π/4) * dx
|ψ(L/4)|^2dx = (2/L) * (1/2) * dx
|ψ(L/4)|^2dx = dx/L
Therefore, the probability of finding the particle in the interval x=L/4 to x=L/4+dx is dx/L.
Part B:
To calculate the probability of finding the particle in the interval x to x+dx for x=L/2, we need to calculate the value of |ψ(x)|^2 at x=L/2 and multiply it by dx. Therefore, we have:
|ψ(L/2)|^2dx = (2/L) * sin^2(π/2) * dx
|ψ(L/2)|^2dx = (2/L) * dx
|ψ(L/2)|^2dx = 2dx/L
Therefore, the probability of finding the particle in the interval x=L/2 to x=L/2+dx is 2dx/L.
Part C:
To calculate the probability of finding the particle in the interval x to x+dx for x=3L/4, we need to calculate the value of |ψ(x)|^2 at x=3L/4 and multiply it by dx. Therefore, we have:
|ψ(3L/4)|^2dx = (2/L) * sin^2(3π/4) * dx
|ψ(3L/4)|^2dx = (2/L) * (1/2) * dx
|ψ(3L/4)|^2dx = dx/L
Therefore, the probability of finding the particle in the interval x=3L/4 to x=3L/4+dx is dx/L.
Learn more about wave function here : brainly.com/question/28189732
#SPJ11