calculate the grams of salicylic acid that is needed to prepare a 50-ml volumetric solution of 2.50×10-3 m salicylic acid? show all your work. molar mass of salicylic acid = 138.121g/mol

We cannot determine if there is an azeotrope in the system of carbon tetrachloride and 1,2-dichloroethane without examining the vapor-liquid equilibrium data, but we know that pressure can influence the presence of an azeotrope.

Based on the given information, we can determine if the system of carbon tetrachloride (1) and 1,2-dichloroethane (2) has an azeotrope. An azeotrope is a mixture of two or more substances that has a constant boiling point and composition, meaning it cannot be separated by distillation.

To determine if this system has an azeotrope, we need to examine the vapor-liquid equilibrium data at 1 bar pressure. If the data shows a point where the vapor and liquid phases have the same composition, then an azeotrope exists.

Without the table of vapor-liquid equilibrium data, we cannot determine if there is an azeotrope in this system. However, we do know that pressure plays a role in determining if an azeotrope exists. Changing the pressure can cause the composition and boiling point of the mixture to change, which can affect the presence of an azeotrope.

In summary, we cannot determine if there is an azeotrope in the system of carbon tetrachloride and 1,2-dichloroethane without examining the vapor-liquid equilibrium data, but we know that pressure can influence the presence of an azeotrope.

Learn more about pressure here:

https://brainly.com/question/32314042

#SPJ11

Patients with galactosemia follow a lactose-restricted diet. This depends on a deficiency of sucrose in the diet is Lactose intolerance.

Signs of lactose intolerance include nausea, cramps, fuel, bloating, or diarrhea within 30 minutes to 2 hours after ingesting milk or dairy products. Signs occur due to the fact there isn't always sufficient lactase being produced by the body to digest the lactose fed on.

Without lactase, the body can't well digest food that has lactose in it. because of this if you consume dairy meals, the lactose from these foods will skip into your intestine, which could cause fuel, cramps, a bloated feeling, and diarrhea, that's free watery poop.

You could take lactase pills before you eat or drink milk products. you may additionally upload lactase drops to exploit before you drink it. The lactase breaks down the lactose in food and drinks, lowering your chances of having lactose intolerance signs and symptoms. test along with your medical doctor earlier than using lactase merchandise.

To know more about galactosemia here

https://brainly.com/question/16002413

#SPJ4

Answer;Part A:

To find the standard enthalpy change for the reaction:

C(s) + CO2(g) → 2CO(g)

We need to use the standard enthalpies of formation for each of the compounds involved, which can be found in Appendix B of the textbook:

C(s): ΔH°f = 0 kJ/mol

CO2(g): ΔH°f = -393.5 kJ/mol

CO(g): ΔH°f = -110.5 kJ/mol

Using the equation:

ΔH°rxn = ΣΔH°f(products) - ΣΔH°f(reactants)

we can calculate the standard enthalpy change for the reaction:

ΔH°rxn = 2(ΔH°f[CO]) - ΔH°f[CO2] - ΔH°f[C]

ΔH°rxn = 2(-110.5 kJ/mol) - (-393.5 kJ/mol) - 0 kJ/mol

ΔH°rxn = -283.0 kJ/mol

Therefore, the standard enthalpy change for the reaction is -283.0 kJ/mol.

Part B:

To find the standard enthalpy change for the reaction:

2H2O2(aq) → 2H2O(l) + O2(g)

We can use the standard enthalpies of formation for each of the compounds involved, which can be found in Appendix B of the textbook:

H2O2(aq): ΔH°f = -187.8 kJ/mol

H2O(l): ΔH°f = -285.8 kJ/mol

O2(g): ΔH°f = 0 kJ/mol

Using the equation:

ΔH°rxn = ΣΔH°f(products) - ΣΔH°f(reactants)

we can calculate the standard enthalpy change for the reaction:

ΔH°rxn = 2(ΔH°f[H2O(l)]) + ΔH°f[O2(g)] - 2(ΔH°f[H2O2(aq)])

ΔH°rxn = 2(-285.8 kJ/mol) + 0 kJ/mol - 2(-187.8 kJ/mol)

ΔH°rxn = -196.4 kJ/mol

Therefore, the standard enthalpy change for the reaction is -196.4 kJ/mol.

Part C:

To find the standard enthalpy change for the reaction:

Fe2O3(s) + 3CO(g) → 2Fe(s) + 3CO2(g)

We can use the standard enthalpies of formation for each of the compounds involved, which can be found in Appendix B of the textbook:

Fe2O3(s): ΔH°f = -824.2 kJ/mol

CO(g): ΔH°f = -110.5 kJ/mol

Fe(s): ΔH°f = 0 kJ/mol

CO2(g): ΔH°f = -393.5 kJ/mol

Using the equation:

ΔH°rxn = ΣΔH°f(products) - ΣΔH°f(reactants)

we can calculate the standard enthalpy change for the reaction:

ΔH°rxn = 2(ΔH°f[Fe(s)]) + 3(ΔH°f[CO2(g)]) - (ΔH°f[Fe2O3(s)] + 3(ΔH°f[CO

learn more about  standard enthalpy change

https://brainly.com/question/28303513?referrer=searchResults

#SPJ11

The formula for the complex formed between Ni2+ and carbonate (CO32-) with a coordination number of 4 is [Ni(CO3)2]2-In this complex, the Ni2+ ion is surrounded by four ligands, each donating two electrons to the central metal ion. The carbonate ion (CO32-) acts as a bidentate ligand, meaning it can donate two pairs of electrons to the Ni2+ ion. Therefore, two carbonate ions are needed to form the complex.

The overall charge of the complex is 2-, which means that two negative charges are needed to balance the two positive charges from the Ni2+ ion. This is achieved by having two negatively charged carbonate ions in the complex. The formula [Ni(CO3)2]2- shows that there are two carbonat iones coordinating with one Ni2+ ion.The formula for a complex formed between Ni²⁺ and carbonato (CO₃²⁻) with a coordination number of 4 is [Ni(CO₃)₂]₂⁻.
To know more about carbonate visit

https://brainly.com/question/22530423

#SPJ11

The PAM is a short DNA sequence that is recognized by the Cas9 complex and is required for the cleavage of the target DNA. The target DNA is the DNA sequence that is being modified or edited using the Cas9 complex.

The given question appears to be a collection of terms related to molecular biology and genetic engineering. Cas9 is a DNA endonuclease that is guided by two RNA molecules, crRNA-sp2 and tracrRNA. These molecules form a complex with Cas9 and recognize a specific DNA sequence, called a protospacer, in the target DNA. The protospacer oligonucleotide is a short DNA sequence that is complementary to the protospacer and is used to introduce specific mutations or modifications in the target DNA.
The plasmid DNA is a circular or linearized DNA molecule that can be used as a vector for cloning or expressing genes. The labeled strand partner strand refers to the two complementary strands of DNA that are labeled for visualization purposes. The non-complementary strand binding primer is a short DNA sequence that is used to bind the non-complementary strand of DNA.
The PAM is a short DNA sequence that is recognized by the Cas9 complex and is required for the cleavage of the target DNA. The target DNA is the DNA sequence that is being modified or edited using the Cas9 complex.
In summary, the terms in the question relate to the process of using the Cas9 complex to edit or modify DNA sequences. The answer to the question requires a more specific context or purpose for which these terms are being used.

To know more about molecule visit :

https://brainly.com/question/16555534

#SPJ11

The resulting volume of the gas is approximately 2.14 m^3.

According to Boyle's Law, when the temperature of a gas remains constant, the product of its pressure and volume is constant. Mathematically, P1 * V1 = P2 * V2, where P1 and V1 are the initial pressure and volume, and P2 and V2 are the final pressure and volume, respectively.

Given:

Initial volume (V1) = 5 m^3

Initial pressure (P1) = 300 kPa

Final pressure (P2) = 700 kPa

Rearranging the Boyle's Law equation to solve for the final volume (V2), we get:

V2 = (P1 * V1) / P2

Substituting the given values into the equation, we find:

V2 = (300 kPa * 5 [tex]m^3[/tex]) / 700 kPa

Evaluating the expression, the resulting volume of the gas is approximately 2.14 [tex]m^3[/tex].

Therefore, when the temperature remains unchanged, the resulting volume of the gas is approximately 2.14[tex]m^3[/tex].

Learn more about  Boyle's Law here:

https://brainly.com/question/21184611

#SPJ11

The pressure in a canister full of oxygen gas if the manometer is 418 mm Hg higher on the open end and the atmospheric pressure is 1.04 atm is 373.4 mm Hg.

The force which the substance exerts on another substance per unit area is known as pressure. The pressure of the gas is the force that the gas exerts on the container boundaries.

Barometric pressure is the measurement of air pressure in the atmosphere, specifically the measurement of the weight exerted by air molecules at a given point on Earth.

Given,

Manometer = 418 mmHg

Atmospheric pressure = 1.04 atm

1 atm = 760 mm Hg

so, 1.04 atm = 1.04 × 760

= 790.4 mm Hg

Atmospheric pressure = pressure of manometer + pressure of the gas

790.4 = 418 + Pressure

Pressure of the gas = 790.4 - 418 = 372.4 mm Hg

Learn more about Pressure, here:

https://brainly.com/question/30673967

#SPJ1

The 7.25 mol of [tex]C_2H_6[/tex]  would require approximately 16.06 mol for complete combustion.

To perform the stoichiometric calculation for 7.25 mol of C2H6 reacting with [tex]O_2[/tex] , we need to determine the balanced equation for the reaction. The balanced equation for the combustion of ethane (C2H6) with oxygen (O2) is:

[tex]C_2H_6 + 7/2 O_2 → 2 CO_2 + 3 H_2O[/tex]

The stoichiometric ratio between [tex]C_2H_6[/tex] and [tex]O_2[/tex] in this reaction is 1:7/2 (or 2:7), meaning that for every 2 moles of [tex]C_2H_6[/tex] , we need 7/2 (or 3.5) moles of [tex]O_2[/tex]

Now, we can use this stoichiometric ratio to calculate the amount of [tex]O_2[/tex] required for 7.25 mol of [tex]C_2H_6[/tex].

Moles of [tex]O_2[/tex] = (7.25 mol [tex]C_2H_6[/tex] ) × (7/2 mol [tex]O_2[/tex] / 2 mol [tex]C_2H_6[/tex])

Moles of [tex]O_2[/tex] ≈ 16.06 mol

Therefore, 7.25 mol of [tex]C_2H_6[/tex]  would require approximately 16.06 mol for complete combustion.

It is important to note that this calculation assumes the reactants are in stoichiometric proportions, meaning that there is an excess of [tex]O_2[/tex] available for the reaction. In practical scenarios, the actual amount of [tex]O_2[/tex] used might differ based on the limiting reactant.

Learn more about stoichiometric here:

https://brainly.com/question/11130137

#SPJ11

1.73 minutes are required to deposit 2.61 g cr from a cr³⁺(aq) solution using a current of 2.50 a

Electroplating is a process of depositing a metal onto a conductive surface by using electrolysis. In this process, an electric current is passed through an electrolyte solution containing ions of the metal to be deposited. The metal ions are reduced at the cathode, which is the surface where the metal is being deposited. The rate at which the metal is deposited depends on the current and the time for which the current is applied.

To calculate the time required to deposit a certain amount of metal, we can use Faraday's law of electrolysis, which states that the amount of metal deposited is proportional to the amount of electric charge that passes through the cell. The equation for this is:

mass of metal deposited = (current x time x atomic mass of metal) / (Faraday's constant x charge on ion)

In this problem, we are given the current (2.50 A), the mass of metal to be deposited (2.61 g), the charge on the Cr³⁺ ion (3+), and the Faraday's constant (96,500 C/mol). The atomic mass of Cr is 52.0 g/mol.

Substituting these values into the equation, we get:

2.61 g = (2.50 A x time x 52.0 g/mol) / (96,500 C/mol x 3)

Simplifying this equation gives:

time = (2.61 g x 96,500 C/mol x 3) / (2.50 A x 52.0 g/mol)

time = 103.9 s or 1.73 minutes (rounded to two decimal places)

Therefore, it would take approximately 1.73 minutes to deposit 2.61 g of Cr from a Cr³⁺(aq) solution using a current of 2.50 A.

Learn more about Electrolysis at: https://brainly.com/question/16929894

#SPJ11

When excess KOH solution is added to 65.0 ml of 0.728 M CuSO4 solution, 4.62 grammes of Cu(OH)2 will precipitate.

The reaction's chemically balanced equation is as follows:

Cu(OH)2(s) + K2SO4(aq) = CuSO4(aq) + 2KOH(aq)

To begin with, we must determine how many moles of CuSO4 are in the solution:

0.0650 L = 0.0473 mol; n(CuSO4) = M V = 0.728 mol/L

In accordance with the balanced equation's stoichiometry, 1 mole of CuSO4 reacts with 2 moles of KOH to create 1 mole of Cu(OH)2. Consequently, the amount of Cu(OH)2 that was produced is:

1 mol Cu(OH)2 divided by 1 mol CuSO4 yields n(Cu(OH)2) = 0.0473 mol CuSO4

Using its molar mass, we can finally determine the mass of Cu(OH)2 formed:

M(Cu(OH)2) = 0.0473 mol 97.56 g/mol = 4.62 g where m(Cu(OH)2) = n(Cu(OH)2)

For more such questions on stoichiometry

https://brainly.com/question/16060223

#SPJ11

Answer:

-2247 kJ.

Explanation:

If you want to calculate the free energy change of a reaction at 25 ∘C, you need to follow these simple steps:

Congratulations! You have successfully calculated the free energy change of a reaction at 25 ∘C using some basic chemistry concepts and formulas. Now you can impress your friends and family with your newfound knowledge and skills!

The energy diagram, consisting of seven bins, will be labeled, and the corresponding reaction will be identified.

An energy diagram represents the energy changes that occur during a chemical reaction. In this case, the energy diagram will consist of seven bins, which represent different energy levels or states of the reactants and products.

To label the energy diagram, each bin will be assigned a corresponding energy value. The reactants will be placed in a specific bin, indicating their initial energy level.

The energy barrier or transition state will be identified as the highest point on the energy diagram, separating the reactants from the products. The products will be placed in another bin, indicating their final energy level.

Once the energy diagram is labeled, the corresponding reaction can be identified by considering the changes in energy during the reaction. The reactants will have a higher energy than the products, and the energy barrier represents the activation energy required for the reaction to proceed.

By examining the energy changes and transitions depicted on the energy diagram, it becomes possible to determine which specific reaction the diagram corresponds to. The energy diagram provides a visual representation of the energy profile of the reaction, aiding in the understanding of the reaction's thermodynamics and kinetics.

Learn more about corresponding reaction here:

https://brainly.com/question/28892861

#SPJ11

The correct mineral that is commonly used for filtering water, especially drinking water, is diatomite.                                    

Diatomite is a porous, sedimentary rock made up of the fossilized remains of diatoms, a type of algae. Due to its highly porous structure, diatomite has excellent filtration properties, making it a popular choice for water filtration. Its ability to remove impurities such as bacteria, viruses, and heavy metals makes it an effective mineral for ensuring clean and safe drinking water.
Other minerals listed, such as Cadmium, Kaolin, Tantalum, and Zinc, do not possess the same filtering properties as Diatomite and are not commonly used for this purpose.

Learn more about diatomite here:
https://brainly.com/question/13506179

#SPJ11

By plotting ln[C2H4O] versus time and obtaining a straight line with a negative slope, we can determine the value of the rate constant k and verify that the reaction is first-order.

To verify that a reaction is first-order, the concentration of the reactant must be monitored over time and plotted on a graph. In this case, we will plot the natural logarithm of the concentration of ethyl acetate, [tex]ln[C_2H_4O][/tex], versus time.

Assuming the reaction follows first-order kinetics, the plot should yield a straight line with a negative slope. The equation for a first-order reaction is:

[tex]ln[C_2H_4O] = -kt + ln[C_2H_4O]_0[/tex]

where k is the rate constant, t is time,[tex][C_2H_4O]_0[/tex] is the initial concentration of ethyl acetate, and[tex]ln[C_2H_4O][/tex]is the natural logarithm of the concentration of ethyl acetate at time t.

By plotting[tex]ln[C_2H_4O][/tex] versus time and determining the slope of the line, we can calculate the rate constant k. If the plot yields a straight line with a negative slope, this indicates that the reaction is first-order.

If experimental data shows a linear relationship between [tex]ln[C_2H_4O][/tex] and time, then the slope of this line will give the rate constant (k) for the reaction.

For more question on rate constant visit:

https://brainly.com/question/24749252

#SPJ11

The red cabbage acid-base indicator is a popular choice for identifying the pH of a solution. It works by changing color in response to the acidity or basicity of the solution. However, it may not be suitable for use as an indicator in titrations.

Titrations are a precise method of determining the concentration of a solution by reacting it with a solution of known concentration (the titrant). This reaction is carried out until a specific end point is reached, which is usually identified by a color change in the indicator.
The problem with using red cabbage as an indicator in titrations is that it is not a reliable indicator for the endpoint. This is because the color change is not sharp enough, and the range over which it changes color is relatively broad. This can make it difficult to accurately identify the endpoint, which can result in inaccurate titration results.
Therefore, it is more common to use a specific indicator that is known to produce a sharp, distinctive color change at the end point of the titration. These indicators are carefully chosen to match the pH range of the titration, which ensures the accuracy and reliability of the results.
In summary, while the red cabbage acid-base indicator is a useful tool for identifying the pH of a solution, it is not suitable for use as an indicator in titrations. Titrations require a more specific indicator that can produce a sharp and reliable color change at the endpoint.

To learn more about red cabbage acid-base indicator, refer:-

https://brainly.com/question/16060048

#SPJ11

The reaction between a weak acid and a strong base results in the formation of a salt and water.

When a weak acid reacts with a strong base, they undergo a neutralization reaction. The acid donates a proton (H+) to the base, forming water and a salt. Since the acid is weak, it does not completely dissociate in water, resulting in a partial reaction. The strong base, on the other hand, completely dissociates into ions. The formation of water and a salt in the reaction leads to a decrease in the concentration of H+ ions in the solution. As a result, the pH of the solution increases and becomes more basic compared to the initial pH of the weak acid.

To learn more about osmotic pressure, click here:

brainly.com/question/29819107

#SPJ11

There are approximately 1.11 x 10^22 atoms of mercury in 1.37 mL of mercury. to calculate the number of atoms, we need to first determine the mass of 1.37 mL of mercury using its density.

Density is defined as mass per unit volume, so we can calculate the mass of 1.37 mL of mercury as:

mass = density x volume

mass = 13.5 g/mL x 1.37 mL

mass = 18.495 g

Next, we need to convert the mass of mercury into the number of atoms. To do this, we use the molar mass of mercury, which is 200.59 g/mol. We can calculate the number of moles of mercury as:

moles = mass / molar mass

moles = 18.495 g / 200.59 g/mol

moles = 0.0922 mol

Finally, we can convert moles of mercury into the number of atoms using Avogadro's number, which is 6.022 x 10^23 atoms/mol:

number of atoms = moles x Avogadro's number

number of atoms = 0.0922 mol x 6.022 x 10^23 atoms/mol

number of atoms = 1.11 x 10^22 atoms

Therefore, there are approximately 1.11 x 10^22 atoms of mercury in 1.37 mL of mercury.

Learn more about mercury here:

https://brainly.com/question/4025230

#SPJ11

We need to identify the limiting reactant, which is the reactant that is completely consumed and determines the maximum amount of product that can be formed, we found the maximum amount of Chromium (III) Phosphate formed is 107.35 g.

First, we need to calculate the number of moles for each reactant. The molar mass of Chromium (Cr) is 52 g/mol, and the molar mass of Phosphoric acid (H3PO4) is 98 g/mol.

Number of moles of Chromium = 25.0 g / 52 g/mol = 0.481 moles

Number of moles of Phosphoric acid = 57.0 g / 98 g/mol = 0.581 moles

Next, we determine the stoichiometric ratio between Chromium (III) Phosphate (CrPO4) and the reactants from the balanced equation. The balanced equation is: 3Cr + 2H3PO4 → CrPO4 + 3H2

From the equation, we can see that 3 moles of Chromium (Cr) react with 2 moles of Phosphoric acid (H3PO4) to form 1 mole of Chromium (III) Phosphate (CrPO4). Comparing the moles of reactants to the stoichiometric ratio, we find that 0.481 moles of Chromium is less than the required 1 mole of Chromium for the reaction. Therefore, Chromium is the limiting reactant.

Since 1 mole of Chromium (III) Phosphate has a molar mass of 107.35 g, the maximum amount of Chromium (III) Phosphate formed is 107.35 g.

LEARN MORE ABOUT limiting reactant here: brainly.com/question/10255265

#SPJ11

If temperature measurements at the condenser outlet tubing and the end of the liquid line differ significantly, the high-side restriction is caused by the txv. The following statement is False.

If temperature measurements at the condenser outlet tubing and the end of the liquid line differ significantly, it is not necessarily an indication that the high-side restriction is caused by the thermal expansion valve (TXV).  Temperature differences between these two points can be influenced by various factors such as ambient conditions, refrigerant charge level, airflow across the condenser, and overall system efficiency. A significant temperature difference may suggest an issue with the condenser, such as inadequate heat transfer or airflow restriction.

A high-side restriction could be caused by multiple factors, including a clogged filter drier, a blockage in the condenser coil, or a malfunctioning valve. It would require a thorough evaluation of the refrigeration system, including pressure measurements, to accurately diagnose the cause of the restriction. It's important to consult with a qualified HVAC technician or refrigeration specialist to diagnose and resolve any issues with the refrigeration system. They can conduct a comprehensive assessment and perform the necessary troubleshooting to determine the root cause of the problem.

Learn more about thermal expansion valve here:

https://brainly.com/question/32157222

#SPJ11

To find the volume of the red blood cell, if the cell has a cylindrical shape with a diameter of 6 ×10⁻⁶m and a height of 2 ×10⁻⁶m, we can use the formula for the volume of a cylinder, which is:

Volume = m x (radius² x height)

First, we need to convert the diameter of the cell to its radius, which is half the diameter. So the radius would be:

radius = (6 × 10⁻⁶m / 2)= 3 × 10⁻⁶m

Now we can plug in the values for radius and height into the formula and solve for the volume:

Volume = п x (3 × 10⁻⁶m)² × 2 × 10⁻⁶m

Volume = 56.55 × 10⁻¹⁸ m³

To convert this to cubic centimetres, we can use the fact that 1 cm³ = 10⁻⁶ m³. So the volume of the red blood cell in

cubic centimeters would be:

Volume = 56.55 × 10⁻¹⁸ m³ x (1 cm³ / 10⁻⁶ m³)

Volume = 5.655 × 10⁻¹¹ cm³

Therefore, the volume of the red blood cell is approximately 5.655 × 10⁻¹¹ cubic centimetres.

for more questions on volume of red blood cell: https://brainly.com/question/30471112

#SPJ11

The volume of the red blood cell with given dimensions, in cubic centimeters, is 56.5 × 10⁻¹².

To calculate the volume of a cylinder, we use the formula V = πr²h. Here V is the volume, r is the radius, h is the height, and π is Pi approximately equal to 3.14159. For the red blood cell, the diameter is 6 ×10⁻⁶m, which means the radius r will be half of the diameter, which is 3 ×10⁻⁶m. The height h is given as 2 ×10⁻⁶m. Insert these values into the formula results in V = π(3 ×10⁻⁶m)²(2 ×10⁻⁶m) = 56.5 × 10⁻¹⁸ cubic meters. However, the question asks us for the volume in cubic centimeters, so we must convert from cubic meters to cubic centimeters. Because 1 cubic meter equals 1×10⁶ cubic centimeters, the conversion results in V = 56.5 × 10⁻¹² cubic centimeters.

https://brainly.com/question/32488277

#SPJ2

No, the Grignard synthesis would not proceed as expected if a chemist used 100% ethanol rather than diethyl ether as the reaction solvent.

The Grignard synthesis is a powerful tool used in organic chemistry for creating carbon-carbon bonds. The reaction involves the reaction of an organomagnesium halide (Grignard reagent) with a carbonyl compound, such as an aldehyde or ketone. The reaction takes place in an anhydrous environment, typically using diethyl ether as the solvent.

However, if a chemist were to mistakenly use 100% ethanol instead of diethyl ether as the reaction solvent, the Grignard synthesis would not proceed as expected. This is because ethanol is a polar solvent, unlike diethyl ether, which is a nonpolar solvent. As a result, the Grignard reagent would be significantly less soluble in ethanol, and the reaction may not even take place at all.

Learn more about Grignard synthesis

brainly.com/question/30887376

#SPJ11

To find the partial pressure of kr in the mixture, we need to use the mole fraction of kr in the mixture. The mole fraction of a gas component in a mixture is the number of moles of that gas divided by the total number of moles of all the gases in the mixture.

So, the total number of moles in the mixture is:

0.220 moles kr + 0.350 moles Cl2 + 0.640 moles He = 1.21 moles

•The mole fraction of kr is:

0.220 moles kr / 1.21 moles total = 0.182

•The mole fraction of Cl2 is:

0.350 moles Cl2 / 1.21 moles total = 0.289

•The mole fraction of He is:

0.640 moles He / 1.21 moles total = 0.529

Now, to find the partial pressure of kr, we need to multiply the total pressure of the mixture by the mole fraction of kr:

Partial pressure of kr = 2.95 atm x 0.182 = 0.5369 atm

Therefore, the partial pressure of kr in the mixture is 0.5369 atm.

Know more about Partial pressure here :

brainly.com/question/13199169

#SPJ11

1) London dispersion forces, dipole-dipole interactions, and hydrogen bonding are all intermolecular forces that exist between molecules.

London dispersion forces (also called Van der Waals forces) are the weakest type of intermolecular force. They occur due to temporary fluctuations in electron distribution, resulting in the formation of temporary dipoles. These temporary dipoles induce other temporary dipoles in neighboring molecules, leading to attractive forces between them. London dispersion forces are present in all molecules, regardless of polarity.

Dipole-dipole interactions occur between polar molecules. These molecules have a permanent dipole moment due to the presence of polar bonds. The positive end of one molecule is attracted to the negative end of another molecule, resulting in dipole-dipole interactions. Dipole-dipole interactions are stronger than London dispersion forces.

Hydrogen bonding is a specific type of dipole-dipole interaction that occurs when hydrogen is bonded to highly electronegative elements like nitrogen, oxygen, or fluorine. In hydrogen bonding, the hydrogen atom forms a polar covalent bond with the electronegative atom, and the partially positive hydrogen atom is attracted to the lone pairs of electrons on another electronegative atom in a different molecule. Hydrogen bonding is the strongest type of intermolecular force and plays a crucial role in many biological and chemical systems.

2) For hydrogen bonding to occur, there must be a hydrogen atom covalently bonded to a highly electronegative element (nitrogen, oxygen, or fluorine). The hydrogen atom must have a partial positive charge due to the electronegativity difference between hydrogen and the electronegative atom. The electronegative atom must also have lone pairs of electrons available to form hydrogen bonds with other molecules.

3) The student is incorrect. CH2O (formaldehyde) does not have hydrogen bonding. Although it contains hydrogen and oxygen, the oxygen atom in formaldehyde is not bonded to the hydrogen atom. In order for hydrogen bonding to occur, the hydrogen atom must be directly bonded to the highly electronegative atom. In formaldehyde, the oxygen atom is bonded to the carbon atom, and the hydrogen atom is bonded to the carbon atom. Thus, formaldehyde does not have the necessary covalent bonds for hydrogen bonding to take place.

To learn more about  bond click here:

brainly.com/question/29753213

#SPJ11

Peptide bonds are covalent bonds that form between amino acids. Peptide bonds involve the condensation of the carboxyl group of one amino acid with the amino group of another amino acid.

All four statements are true. Peptide bonds are covalent bonds that form between the carboxyl group of one amino acid and the amino group of another amino acid. This condensation reaction results in the formation of a peptide bond, with the loss of a water molecule. Peptide bonds have partial double bond character due to resonance stabilization, resulting in a planar structure. This rigidity is important for the folding and stability of proteins. Hydrolysis of peptide bonds can occur under acidic or basic conditions, where the peptide bond is cleaved by the addition of a water molecule, forming two separate amino acids. This process is important for protein degradation and digestion.

Learn more about amino acid here;

https://brainly.com/question/15687833

#SPJ11

The elements lithium and oxygen react explosively to form lithium oxide. 2.22 moles of lithium oxide is produced from 4.45 moles of lithium.

The reaction of lithium and oxygen to form lithium oxide can be written as:

4Li + O₂ → 2Li₂O

From the above equation, it is observed that 4 moles of lithium react with one mole of oxygen to form two moles of lithium oxide.

To calculate the moles of lithium oxide produced from 4.5 moles of lithium:

4 moles of lithium are required to form 2 moles of lithium oxide.

4.45 moles of lithium will produce x moles of lithium oxide.

4.45 × 2 = 4 × x

x= 8.9 ÷ 4

x= 2.22 moles

To learn more about lithium, refer to the link:

https://brainly.com/question/27642226

#SPJ1

To calculate the required milliliters of 15m hydrogen peroxide solution, we need to use the formula:
M1V1 = M2V2
Where M1 is the initial concentration, V1 is the initial volume, M2 is the final concentration, and V2 is the final volume.
Substituting the given values, we get:
15m x V1 = 0.85m x 250ml
V1 = (0.85m x 250ml) / 15m

Therefore, 14.17ml of a 15m hydrogen peroxide solution is required to prepare 250ml of 0.85m solution.
To find out how many milliliters of a 15M hydrogen peroxide solution are required to prepare 250mL of a 0.85M solution, you can use the dilution formula:
M1V1 = M2V2
Where M1 and V1 represent the initial molarity and volume, and M2 and V2 represent the final molarity and volume. In this case, M1 is 15M, M2 is 0.85M, and V2 is 250mL. You need to find V1.

Rearranging the formula to solve for V1:
V1 = (M2V2) / M1
Now, plug in the values:
V1 = (0.85M * 250mL) / 15M
V1 = (212.5) / 15
V1 ≈ 14.17mL
So, approximately 14.17 milliliters of a 15M hydrogen peroxide solution are required to prepare 250mL of a 0.85M solution.

To know more about Hydrogen Peroxide visit-

https://brainly.com/question/29102186

#SPJ11

Using an asymmetric catalytic hydrogenation, the starting alkene that  used to make l-histidine would be 1,2,4-triazole-3-amine.

L-Histidine is an amino acid commonly used in protein synthesis and is an important component of human nutrition. Asymmetric catalytic hydrogenation is a powerful tool in organic synthesis that can be used to create chiral centers with high enantioselectivity. In order to produce L-histidine using asymmetric catalytic hydrogenation, the starting alkene must be chosen carefully.

L-Histidine contains an imidazole ring, so the starting alkene should contain an imidazole group or a precursor that can be converted to an imidazole. One possible starting alkene is 1,2,4-triazole-3-amine, which can be hydrogenated using a chiral ruthenium catalyst to produce L-histidine.

Overall, the choice of starting alkene for the synthesis of L-histidine using asymmetric catalytic hydrogenation requires careful consideration of the functional groups and the ability of the catalyst to achieve high enantioselectivity.

Learn more about hydrogenation at: https://brainly.com/question/14170443

#SPJ11

Delta H for the reaction B + D --> E + 2C can be calculated by adding the enthalpies of the individual reactions in the reverse order and then multiplying them by their respective coefficients.

Therefore, Delta H = [(2C + D --> 3B) + (B --> 1/2A)] x (-1) + (A + E --> 2D)

Delta H = [(3/2A --> 2C + D) + (B --> 1/2A)] + (A + E --> 2D)

Delta H = (3/2A --> 2C + D) + (B --> 1/2A) + (A + E --> 2D)

Delta H = -125 kJ + 300 kJ + 350 kJ = 525 kJ (Answer)

The assumption of kinetic molecular theory that is not correct is (e) All of these are correct. The kinetic molecular theory assumes that gas particles have negligible volume and no intermolecular forces, which is not always true. In reality, gas particles do have a small but nonzero volume and can experience intermolecular attractions or repulsions under certain conditions.

learn more about reaction here:

https://brainly.com/question/28984750

#SPJ11

The order of increasing electronegativity for the halogens is: astatine < iodine < bromine < chlorine.

Electronegativity is the ability of an atom to attract electrons towards itself in a chemical bond. The trend for electronegativity increases from left to right across a period and decreases down a group in the periodic table.

In order of increasing electronegativity, the elements chlorine, bromine, iodine, and astatine can be arranged. Chlorine has the highest electronegativity, followed by bromine, iodine, and astatine.

Chlorine, with an electronegativity of 3.16, is the most electronegative element among the halogens. Bromine has an electronegativity of 2.96, which is slightly lower than chlorine. Iodine has an electronegativity of 2.66, which is lower than both chlorine and bromine. Astatine has the lowest electronegativity of the halogens, with a value of approximately 2.2.

For more such questions on electronegativity:

https://brainly.com/question/17762711

#SPJ11

The order of increasing electronegativity is: astatine < iodine < bromine < chlorine.

An element's propensity to draw electrons to itself when it is chemically connected to another element is known as electronegativity. In the periodic table, it decreases down a group and rises from left to right across a period. In this instance, we must arrange the elements astatine (At), chlorine (Cl), iodine (I), and bromine (Br) in ascending order of electronegativity.

The electronegativity rises across the halogen group in the periodic table from left to right. As a result, these elements' electronegativity is growing in the following order:

At I, Br, and Cl

Astatine, among these elements, has the lowest electronegativity, whereas chlorine has the greatest.

learn more about electronegativity here:

https://brainly.com/question/17762711

#SPJ11

A) I and II are both spontaneous.

You can learn more about spontaneous at: https://brainly.com/question/12319501

#SPJ11