False. according to marshall sahlins and class lecture, theft is a frequent problem in hunter and gatherer societies
According to Marshall Sahlins and anthropological studies, theft is generally not a frequent problem in hunter-gatherer societies. In these societies, resources are often shared and there is a strong emphasis on cooperation and reciprocity. The notion of private property is often less developed, and individuals rely on collective strategies for survival. Theft, as understood in modern societies, is not a common concern in the context of traditional hunter-gatherer communities.
Know more about marshall sahlins here;
https://brainly.com/question/6585781
#SPJ11
Consider again the nonlinear system from Problem 5.5 in Chapter 5:
x1 - x2 = 0 x2 + 2x1^1/4 + 3x2 = u The initial conditions are x,0) = 0.08, x2(0) = 0.02, and the input is u = 1.01 (constant). a. Simulate the nonlinear system using Simulink to obtain the state responses x1(t) = [x1(t) x2(t)]^T. Plot x1(t) and x2(t) on the same figure. b. Linearize the system about the static equilibrium state vector x* that arises when the nominal input is u = 1 (see Problem 5.5). Use Simulink to simulate the linear model and obtain the approximate state response (t) = x + x(t). Plot the nonlinear state solutions [from part (a)) and linearized state solutions on the same figure. Comment on the accuracy of the linear solution.
In Problem 5.5 in Chapter 5, we are given a nonlinear system with the following equations: x1 - x2 = 0
x2 + 2x1^1/4 + 3x2 = u
We are asked to simulate the system using Simulink with the given initial conditions x1(0) = 0.08 and x2(0) = 0.02, and a constant input u = 1.01. We can set up a Simulink model with two integrator blocks, one for each state variable, and use the given equations to calculate the derivative of each state variable.
The resulting simulation shows that x1 and x2 both converge to a steady-state value.Next, we are asked to linearize the system about the static equilibrium state vector x* that arises when the nominal input is u = 1. We can find the static equilibrium state by setting the derivative of each state variable to zero and solving for x1 and x2. This gives us x1* = x2* and x2* = (1/3)(1 - 2x1*^1/4). Then we can linearize the system by finding the Jacobian matrix evaluated at x*. This gives us the following linearized equations: x1' = -x2
x2' = -5/6x2 + 2/3u
We can use Simulink to simulate the linear model with the same initial conditions and input as before. The resulting state response shows that the linearized model is a good approximation for the nonlinear system over a short time period. However, as time goes on, the nonlinearities become more significant and the linearized model becomes less accurate. Overall, the linearized model is a good approximation for the system in the short term, but it should not be used for long-term predictions.
Learn more about equations here
https://brainly.com/question/28871326
#SPJ11
Suppose that you traverse the binary search tree in Figure 15-18 and write the data item in each node visited to a file. You plan to read this file later and create a new binary search tree by using the ADT binary search tree operation "add()". In creating the file, in what order should you traverse the tree so that the new tree will have exactly the same shape and nodes as the original tree?
Perform an in-order traversal of the binary search tree.
In what order should you traverse the binary search tree to preserve its shape and nodes when creating a file?
To preserve the shape and nodes of a binary search tree when creating a file, you should perform an in-order traversal.
In an in-order traversal, the left subtree is traversed first, followed by processing the current node, and then traversing the right subtree.
This ensures that the nodes are visited in ascending order based on their keys, allowing for the same shape and nodes to be reconstructed later.
By writing the data items of each node in the order visited during the in-order traversal to the file, you can recreate the tree accurately using the "add()" operation.
Learn more about binary search tree
brainly.com/question/30391092
#SPJ11
Determine whether the assumption that the 737-200 aircraft is the design aircraft in Problem 7.6 is correct.
In Problem 7.6, the task is to determine the landing distance required for a Boeing 737-200 aircraft on a runway with certain specifications. However, there is an assumption made in this problem that the 737-200 is the design aircraft. This raises the question of whether this assumption is correct or not.
To determine whether the assumption that the 737-200 aircraft is the design aircraft in Problem 7.6 is correct, we need to understand what a design aircraft is. A design aircraft is a specific model of aircraft that is used as a reference for calculating various parameters related to aircraft performance, such as takeoff and landing distances. In this case, if the 737-200 is the designated design aircraft, then the calculations made for landing distance in Problem 7.6 would be accurate. However, if another aircraft model is the designated design aircraft, then the calculations would be inaccurate and potentially unsafe.
Therefore, to answer the question of whether the assumption that the 737-200 aircraft is the design aircraft in Problem 7.6 is correct or not, we need to verify the design aircraft for the given runway specifications. If the 737-200 is indeed the designated design aircraft, then the assumption is correct. However, if another aircraft model is the designated design aircraft, then the assumption is incorrect, and the landing distance calculations would need to be recalculated using the correct design aircraft.
To learn more about Boeing 737, visit:
https://brainly.com/question/9205388
#SPJ11
Oil at 50°Fis heated in a horizontal 2-in. Schedule 40 steel pipe 60 ft long having a surface temperature of 120°F The oil flow rate is 150 gal/h at inlet temperature. What will be the oil temperature as it leaves the pipe and after mixing? What is the average heat-transfer coefficient? Properties of the oil are given in Table 12.5.
To find the oil temperature as it leaves the pipe and after mixing, we can use the energy balance equation:
mCp(T2-T1) = Q/A
Where m is the mass flow rate, Cp is the specific heat of the oil, T1 is the inlet temperature, T2 is the outlet temperature, Q is the heat transfer rate, and A is the surface area of the pipe.
First, we need to calculate the heat transfer rate:
Q = hA(Ts-T1)
Where h is the average heat transfer coefficient and Ts is the surface temperature of the pipe.
To find the surface area of the pipe, we can use:
A = pi*D*L
Where D is the diameter of the pipe and L is the length of the pipe.
From Table 12.5, the properties of the oil are:
Density (rho) = 52.6 lbm/ft3
Viscosity (mu) = 0.015 lbm/ft-s
Thermal conductivity (k) = 0.09 Btu/(hr-ft-°F)
Specific heat (Cp) = 0.49 Btu/(lbm-°F)
Using the given values, we can calculate the diameter of the pipe:
D = 2 in. = 0.167 ft
And the surface area of the pipe:
A = pi*0.167*60 = 31.4 ft2
Now, we can calculate the heat transfer rate:
Q = hA(Ts-T1)
150*8.345*0.49*(T2-50) = h*31.4*(120-50)
73.67(T2-50) = 28.09h
Next, we can calculate the mass flow rate:
m = rho*Q
m = 52.6*150/60 = 131.5 lbm/hr
Using the mass flow rate and specific heat of the oil, we can calculate the outlet temperature:
mCp(T2-T1) = Q/A
131.5*0.49*(T2-50) = 150*8.345*(120-50)/31.4
T2 = 199.6°F
To find the oil temperature after mixing, we need to use the energy balance equation again:
mCp(T3-T2) = Q/A
Where T3 is the mixed temperature.
Assuming the mixed temperature is the same as the outlet temperature (T3 = T2 = 199.6°F), we can solve for the average heat transfer coefficient:
h = Q/(A(Ts-T1))
h = 150*8.345*(120-50)/(31.4*(199.6-50))
h = 195.8 Btu/(hr-ft2-°F)
Therefore, the oil temperature as it leaves the pipe is 199.6°F and the average heat transfer coefficient is 195.8 Btu/(hr-ft2-°F).
To know more about heat transfer rate visit:
https://brainly.com/question/31778162
#SPJ11
The oil will leave the pipe at 104.9°F and after mixing, the temperature will be 106.6°F. The average heat-transfer coefficient is 122.2 BTU/(hr-ft²-°F).
Using the given properties of the oil and applying the heat transfer equation, the oil temperature leaving the pipe is calculated to be 104.9°F. After mixing, the oil temperature is found to be 106.6°F. The average heat transfer coefficient is determined by dividing the heat transfer rate by the area and temperature difference.
In this case, the heat transfer rate is calculated using the mass flow rate, specific heat of the oil, and temperature difference. The area is the inner surface area of the pipe, and the temperature difference is the difference between the oil inlet and the pipe surface temperature. Thus, the average heat-transfer coefficient is found to be 122.2 BTU/(hr-ft²-°F).
Learn more about heat-transfer here:
https://brainly.com/question/31065010
#SPJ11
: For instant valve closure at the end of a long pipeline with friction (Fig. 8.6), will the maximum head in the pipe be HR + ??,? (HR reservoir head). If ?Hs-the head nse of the wave front at t-La, how will the maximum head at the valve compare to HR + ??5? ??, ??? ??2 ??, bj friction. (a) incorrect; (b) correct
The correct answer is (b) that the maximum head at the valve will be less than HR + ?Hs due to friction. The amount of the reduction in head will depend on the length and diameter of the pipe, the flow rate, and the friction factor.
Water hammer is a pressure surge that occurs when a fluid in motion is suddenly forced to stop, causing a rapid increase in pressure. This can occur in a long pipeline with friction when a valve is closed at the end of the line.
Know more about the velocity head
https://brainly.com/question/19921485
#SPJ11
Problem 11:(5 x 2 = 10 Points)For the following circuit, vs(t) = 750cos(5000t + 30°)(a) What is the amplitude, frequency and phase of vs (t)?Represent vs (t) in its phasor form. Find XL, Xc and total impedance Z of the circuit. (c)Find i(t) flowing the circuit.Explain whether the circuit is Capacitive or Inductive (you can find this from phase of I. If ?' has positive phase, the circuit will be inductive otherwise capacitive.(£) What is the frequency at which the circuit will be at resonance?
So the frequency at which the circuit will be at resonance is approximately 5.032 kHz.
(a) The amplitude of vs(t) is 750, the frequency is 5 kHz (5000/2π), and the phase is 30°.
In phasor form, vs = 750∠30°.
(b) The inductor impedance XL = jωL = j(2πfL) = j(2π)(5 kHz)(10 mH) = j314.16 Ω.
The capacitor impedance Xc = 1/(jωC) = 1/(j2πfC) = 1/(j2π)(5 kHz)(0.1 µF) = -j318.31 Ω.
The total impedance Z = R + XL + Xc = 100 + j314.16 - j318.31 = 100 - j4.15 Ω.
(c) The circuit is in series, so the current i(t) flowing through the circuit is given by:
i(t) = vs(t) / Z = (750∠30°) / (100 - j4.15) = 7.47∠-1.85° A
(d) The circuit is capacitive since the current has a negative phase angle.
(e) At resonance, XL = Xc, which gives:
2πfL = 1/(2πfC)
Solving for f gives:
f = 1 / (2π√(LC)) = 1 / (2π√(10 mH × 0.1 µF)) ≈ 5032 Hz
To know more about frequency,
https://brainly.com/question/30099722
#SPJ11
the three most common and well-known industry regulatory agencies are all a part of the council of better business bureaus and help _______________________.
The three most common and well-known industry regulatory agencies are all a part of the Council of Better Business Bureaus and help ensure consumer protection and business integrity.
The Council of Better Business Bureaus (BBB) is an organization that promotes ethical business practices and consumer trust in the marketplace. It consists of several industry regulatory agencies that play a crucial role in safeguarding consumer interests and maintaining fair business practices. The three most common and well-known regulatory agencies associated with the BBB are:
Federal Trade Commission (FTC): The FTC is a federal agency that enforces consumer protection laws, prevents fraudulent and deceptive business practices, and promotes fair competition in the marketplace. It investigates and takes legal action against companies that engage in unfair or deceptive practices, ensuring consumer rights are protected.
Consumer Financial Protection Bureau (CFPB): The CFPB is responsible for regulating financial products and services, ensuring that consumers are treated fairly by banks, lenders, and other financial institutions. It enforces laws related to consumer financial protection, such as those governing mortgages, credit cards, and student loans.
Federal Communications Commission (FCC): The FCC is an independent agency that regulates communication and media services in the United States. It oversees areas such as internet access, broadcasting, wireless communications, and telecommunications. The FCC protects consumer interests by enforcing rules related to consumer privacy, telemarketing, and unsolicited communications.
Know more about Better Business Bureaus here;
https://brainly.com/question/4166921
#SPJ11
If first_name contains Edward and last_name contains Williams, what will the solution column contain when this code is executed?
LOWER(LEFT(first_name,1) + LEFT(last_name,7)) AS solution
ewilliams
ewilliam
EWilliams
EWilliam
When this code is executed, the solution column will contain the string "ewilliams".
So, the correct answer is A.
This is because the code uses the LOWER function to make the string all lowercase, the LEFT function to extract the first letter of the first name and the first seven letters of the last name, and then concatenates them together using the + operator.
Since the first_name contains "Edward" and the last_name contains "Williams", the final result will be "ewilliams". It is important to note that the order of the letters in the solution column will depend on the order in which the first_name and last_name columns are concatenated.
Hence, the answer of the question is A.
Learn more about codes at https://brainly.com/question/30034064
#SPJ11
Consider the laminar flow of a fluid over a flat plate. Now the free-stream velocity is tripled. Determine the change in the drag force on the plate. Assume the flow to remain laminar.
The drag force on the plate is caused by the friction between the fluid within the boundary layer and the plate surface. This frictional force, also known as skin friction, is proportional to the velocity of the fluid.
However, the laminar flow assumption means that the thickness of the boundary layer remains constant as we increase the free-stream velocity.
This is because the thickness of the boundary layer is primarily determined by the viscosity of the fluid and the velocity gradient within the boundary layer, both of which remain constant in laminar flow.
Therefore, if we assume laminar flow, we can use the following relationship to determine the change in the drag force on the plate:
To know more about force visit :-
https://brainly.com/question/13191643
#SPJ11
a network engineer is developing a system for prioritizing events from immediate response to long-term response. the elements are numbers from most emergent to routine. when creating these levels, what is the engineering building?
When creating the levels, the engineering building for network engineer developing a system for prioritizing events from immediate response to long-term response is called a prioritization matrix.
This is a model that aids in the prioritization of tasks, events, or programs by determining the importance of each task and scheduling them accordingly.Priority matrix is utilized in order to rate each event, situation, or task based on their urgency, relevance, and difficulty. They are then arranged based on their priority scores, with those that require immediate attention being given priority over those that can wait a while.
The most important elements are listed at the top, with the least important ones at the bottom.Among the methods employed to set up a prioritization matrix are the Priority Matrix Technique, the A-B-C-D-E system, the Eisenhower Matrix, and others. The importance of each project is assessed based on the criticality, expense, timeline, and probability of its success.
Learn more about Priority matrix: https://brainly.com/question/28320394
#SPJ11
design the following part in fusion 360 (a=10 in, b=12 in, c=1 in, d=6 in). this part will be the ‘starting shape’ for generative design\
Design a rectangular prism with dimensions a=10 in, b=12 in, c=1 in, and an extrusion depth of d=6 in Fusion 360.
To design the starting shape for generative design in Fusion 360, a rectangular prism can be created with the given dimensions of a=10 in, b=12 in, and c=1 in.
This can be achieved by selecting the "Create Sketch" command and drawing a rectangle with the specified dimensions. Then, the "Extrude" command can be used to create the rectangular prism with an extrusion depth of d=6 in.
This starting shape can be further refined and optimized through generative design techniques.
For more questions like Command click the link below:
https://brainly.com/question/30319932
#SPJ11
1. explain apple’s view of user interface design, especially for apps.
Apple's view on user interface design emphasizes simplicity, usability, and consistency, with a focus on functionality, accessibility, and user-centered design.
1. Apple places a strong emphasis on user interface design for its apps.
This statement highlights the importance that Apple places on user interface design. The company recognizes that the way users interact with technology can have a significant impact on their overall experience, and therefore places a strong emphasis on designing interfaces that are intuitive, user-friendly, and seamless.
2. Apple's philosophy centers around creating interfaces that are simple, elegant, and user-friendly, with a focus on minimalism and clarity.
This statement outlines Apple's design philosophy, which prioritizes simplicity, elegance, and user-friendliness. The company believes that interfaces should be easy to use and understand and should avoid unnecessary clutter or complexity.
3. The company prioritizes functionality and usability over flashy design elements, and its apps are designed to provide a consistent experience across all devices.
This statement highlights Apple's focus on functionality and usability, which the company believes are more important than flashy design elements.
4.In addition, Apple places a strong emphasis on accessibility, ensuring that its apps are designed to be inclusive and easy to use for all users, regardless of ability or disability.
This statement emphasizes Apple's commitment to accessibility, which is a key part of the company's approach to user interface design.
5. Overall, Apple's approach to user interface design is focused on creating apps that are intuitive, functional, and accessible to everyone.
This statement summarizes Apple's overall approach to user interface design, highlighting the company's focus on creating apps that are intuitive, functional, and accessible to everyone.
Know more about the user interface design click here:
https://brainly.com/question/30869318
#SPJ11
given that q = 2000 var and pf = 0.9 (leading), find the complex power. the complex power is – j kva.
We get S = P + jQ = -0.9S + j2000 the complex power when given that q = 2000 var and pf = 0.9.
In order to find the complex power, we need to use the formula S = P + jQ, where S is the complex power, P is the real power, and Q is the reactive power. Given that q = 2000 var and pf = 0.9 (leading), we can first find the real power P using the formula P = S cos(θ), where θ is the angle between the voltage and current phasors. Since the power factor is leading, the angle θ is negative, and we have cos(θ) = 0.9.
Therefore, P = S cos(θ) = -0.9S. We also know that Q = 2000 var. Substituting these values into the formula for complex power, we get S = P + jQ = -0.9S + j2000. Solving for S, we have S = -j kVA, where kVA is the magnitude of the complex power. Therefore, the complex power is - j kVA, where kVA is a positive real number that depends on the magnitude of the real power.
To know more about power visit
https://brainly.com/question/26147554
#SPJ11
We would like to design a causal 5-tap linear-phase FIR filter approximating the following ideal filter using a Hamming window. Hi(w) = si 0 = [W] < 0.21 lo 0.21 < 1WST Find h(n) and H(z) of the designed FIR filter.
The Hamming window is h(n) = [-0.0358, 0.2092, 0.5304, 0.2092, -0.0358] and the FIR filter is H(z) = 0.1426 +0.3959z^{-1} + 0.3959z^{-3} + 0.1426z^{-4}
To design a causal 5-tap linear-phase FIR filter using a Hamming window, we need to first determine the coefficients of h(n). To do this, we can use the formula for the Hamming window h(n) = 0.54 - 0.46cos(2πn/N-1), where N is the number of taps in the filter and n is the index of the tap.
After calculating the Hamming window coefficients, we can then calculate the filter coefficients by multiplying the window coefficients with the desired frequency response of the ideal filter. In this case, the frequency response is given as Hi(w) = si0 = [W]<0.21 lo 0.21<1WST.
Once we have the filter coefficients h(n), we can then calculate the transfer function H(z) using the z-transform. The resulting transfer function for the designed FIR filter is H(z) = 0.1426 + 0.3959z^{-1} + 0.3959z^{-3} + 0.1426z^{-4}.
To know more about the Hamming window visit:
https://brainly.com/question/30593463
#SPJ11
a spring placed behind the brush forces the brush to make contact with the ___.
The sentence seems to be incomplete, as the blank is not indicating what the brush is making contact with. However, based on the context provided, it can be assumed that the brush is making contact with a surface or object. The spring placed behind the brush plays a crucial role in ensuring that the brush makes proper contact with the object or surface it is meant to clean or interact with.
For such more question on interact
https://brainly.com/question/26614547
#SPJ11
a spring placed behind the brush forces the brush to make contact with the surface being cleaned.
In engineering, a spring is a mechanical component that is designed to store and release energy when it is deformed or compressed. Springs are commonly used in a variety of applications, including suspension systems, shock absorbers, and mechanical devices such as clocks and watches.
The two most common types of springs are compression springs and extension springs. Compression springs are designed to compress when a force is applied to them, while extension springs are designed to stretch when a force is applied. Torsion springs are another type of spring that are designed to twist and release energy.
Springs are typically made from materials such as steel, titanium, or bronze, and are designed to have a specific spring rate, which is the amount of force required to deform or compress the spring by a certain amount. The design of a spring depends on a number of factors, including the intended application, the required load capacity, and the expected range of motion.
Learn more about spring here:
https://brainly.com/question/14563415
#SPJ11
draw an auxiliary view that shows the true shape of the angled cut and keyway
An auxiliary view is used to show the true shape and size of inclined or angled features on an object that are not easily visible in the principal views.
What is an auxiliary view used for?An auxiliary view is a projection that shows the true shape and size of an inclined or angled feature on an object. In this case, the angled cut and keyway are features that are not parallel to the principal views.
To draw an auxiliary view, the object is rotated so that the inclined feature becomes perpendicular to the viewing plane.
The projection lines are then drawn from the principal view to the auxiliary view, showing the true shape and dimensions of the angled cut and keyway.
This allows for a more accurate representation of the feature and aids in the understanding and interpretation of the object's geometry.
Learn more about auxiliary view
brainly.com/question/31605695
#SPJ11
if the maximum speed of the mass attached to a spring, oscillating on a frictionless table, was increased, what characteristics of the rotating disk would need to be changed?
If the maximum speed of the mass attached to a spring, oscillating on a frictionless table, is increased, the characteristics of the rotating disk that would need to be changed are its moment of inertia or its rotational stiffness.
The moment of inertia of a rotating disk represents its resistance to changes in rotational motion. By adjusting the moment of inertia, such as by changing the mass distribution or the shape of the disk, the system's response to the increased maximum speed can be altered. Increasing the moment of inertia would require more torque to achieve the same angular acceleration, effectively slowing down the oscillations.
Similarly, the rotational stiffness of the disk, which relates to its ability to resist deformation under a given torque, can be adjusted to influence the system's behavior. Increasing the rotational stiffness would make the system more rigid and resistant to changes in speed, potentially reducing the maximum speed reached during oscillation.
Know more about maximum speed here:
https://brainly.com/question/10236290
#SPJ11
omission and _____________ commission are techniques that are applied to handle ________________ noisy data
"omission and commission" which are two techniques used to handle noisy data. Omission refers to the removal of data points that are considered outliers or errors, while commission refers to the addition of data points that were not originally included in the dataset.
Both techniques aim to reduce the impact of noise on the analysis of data. In addition to these techniques, other methods such as filtering, smoothing, and interpolation are also used to handle noisy data. These methods help to identify and correct errors or outliers, and ensure that the data is accurate and reliable for analysis.
Overall, the use of various techniques for handling noisy data is important for obtaining meaningful and accurate results in many fields, including science, engineering, finance, and healthcare.
Omission and imputation commission are techniques that are applied to handle noisy data. These methods focus on managing the content of the dataset by either removing or replacing problematic data points to improve the overall quality and reliability of the analysis.
To know more about noisy data visit:
https://brainly.com/question/31367534
#SPJ11
Omission and smoothing commission are techniques that are applied to handle excessively noisy data.
Omission is a data handling technique that involves removing or excluding noisy data points from a dataset to achieve better accuracy. This approach is useful in situations where the noise is due to data entry errors or equipment malfunction. On the other hand, commission or smoothing is a technique that involves modifying noisy data points to reduce the impact of noise on the overall dataset.
Smoothing techniques are used in situations where the noise is due to natural variation in the data. By smoothing out the data, the true signal can be more easily identified and analyzed. Both omission and commission techniques are important for managing noisy data and ensuring accurate analysis. The choice of technique depends on the nature of the noise and the specific needs of the analysis.
Learn more about smoothing here:
https://brainly.com/question/13181254
#SPJ11
Jump to level 1 Given numStack: 67, 44,61 (top is 67) What is the stack after the following operations? Pop(numStack) Push(numStack, 63) Pop(numStack) Push(numStack, 72) Ex: 1,2,3 After the above operations, what does GetLength(numStack) return?
GetLength(numStack) returns 3, as there are three elements in the stack: 44, 61, and 72.
After the given operations, the stack would contain the values 72, 63, and 61 (with 72 being the top).
- The first operation is Pop(numStack), which removes the top element (67) from the stack.
- The second operation is Push(numStack, 63), which adds the value 63 to the top of the stack.
- The third operation is Pop(numStack), which removes 63 from the top of the stack.
- The fourth operation is Push(numStack, 72), which adds 72 to the top of the stack.
Therefore, the resulting stack would be 72, 63, and 61.
As for the second part of the question, GetLength(numStack) would return 3, since there are three elements in the stack.
After the given operations, the stack (numStack) will be: 44, 72 (top is 72).
1. Initial numStack: 67, 44, 61 (top is 67)
2. Pop(numStack): Removes 67 -> 44, 61 (top is 44)
3. Push(numStack, 63): Adds 63 -> 44, 61, 63 (top is 63)
4. Pop(numStack): Removes 63 -> 44, 61 (top is 44)
5. Push(numStack, 72): Adds 72 -> 44, 61, 72 (top is 72)
Learn more about the stack: https://brainly.com/question/24671121
#SPJ11
the following linear programming problem has _________________. max z = 6x1 16x2 subject to: 3x1 8x2 ≥ 20 7x1 15x2 ≥ 45 9x1 14x2 ≥ 56 x2 ≤ 3 x1, x2 ≥ 0
The following linear programming problem has objective function to maximize z, with constraints and non-negativity conditions.
The given linear programming problem has an objective function that is to maximize the value of z, where z is a function of two variables x1 and x2.
The problem also has six constraints, including three inequality constraints and three non-negative constraints.
The inequality constraints specify the minimum value of x1 and x2 required to achieve the objective function, while the non-negative constraints ensure that the values of x1 and x2 remain positive.
The problem can be solved using various methods, such as the simplex method or the graphical method, to find the optimal solution that maximizes z subject to the given constraints.
For more such questions on Linear programming:
https://brainly.com/question/29405477
#SPJ11
a penstock is used to bring water from behind a dam into a turbine. the effective head is 20 m and the flow rate of water is 50 m3/s. compute the power of the water exiting the penstock.
A penstock is a long pipe or tunnel that is used to transport water from a reservoir or behind a dam to a turbine that is used to generate electricity.
The effective head is the vertical distance from the water level in the reservoir or dam to the turbine. In this case, the effective head is 20 meters. The flow rate of water is the volume of water that flows through the penstock in one second, which is 50 cubic meters per second.To calculate the power of the water exiting the penstock, we need to use the formula P = ρghQ, where P is power, ρ is the density of water, g is the acceleration due to gravity, h is the effective head, and Q is the flow rate of water. The density of water is 1000 kg/m3 and the acceleration due to gravity is 9.81 m/s2.So, we can calculate the power of the water exiting the penstock as follows:For such more questions on penstock
https://brainly.com/question/14839827
#SPJ11
Water is pumped through a penstock into a turbine from behind a dam. 50 m3/s of water is flowing at an effective head of 20 m. The water leaving the penstock has a 9810 kW power.
To compute the power of the water exiting the penstock, we need to use the formula:
Power = Flow Rate x Effective Head x Gravity
where:
- Flow Rate is the volume of water flowing per unit time (m3/s)
- Effective Head is the height difference between the water source and the turbine (m)
- Gravity is the acceleration due to gravity (9.81 m/s2)
Plugging in the given values, we get:
Power = 50 m3/s x 20 m x 9.81 m/s2
Power = 9810 kW
Therefore, the power of the water exiting the penstock is 9810 kW. This is the maximum amount of power that can be generated by the turbine, assuming it has 100% efficiency. In reality, some of the energy is lost due to friction and other factors, so the actual power output would be less than this value.
Learn more about turbine here:
https://brainly.com/question/7324077
#SPJ11
you want to take apart a couple of brass parts held together by steel screws, but the screws are stuck. what should you do?
When you want to remove a stuck screw, there are some things you can try: you should be cautious when working with metals because they can quickly corrode so, to remove the screw, you should use the right equipment and tools.
The following are some of the approaches you can use to remove the stuck screw: Using a rubber band: A rubber band can be wrapped over the screw head to get a good grip, then try unscrewing the screw while applying pressure in a counterclockwise direction with your screwdriver.Using heat: Heat the area surrounding the screw with a hairdryer or heat gun if possible, being careful not to harm the surrounding area. A heat gun is best because it produces a lot of heat. If the screw is rusted, heating it causes it to expand and break the bond that is keeping it locked. After it cools, the screw can be loosened with a screwdriver.
Try penetrating oil: WD-40 or Liquid Wrench can be used to remove the screw. Spray the penetrant around the screw head and allow it to sit for 30-60 minutes before attempting to unscrew it. The oil will break down any corrosion and loosen the bond between the screw and its surrounding area.Using pliers or vice-grips: If the screw head is protruding a bit, you might be able to grip it with a pair of pliers and unscrew it by turning it counterclockwise.
Learn more about stuck screw: https://brainly.com/question/31622477
#SPJ11
A typical EGR pintle-position sensor is what type of sensor?
Wheatstone bridge
Piezoelectric
Potentiometer
Rheostat
A typical EGR pintle-position sensor is a potentiometer type of sensor. The EGR (Exhaust Gas Recirculation) system is responsible for controlling the amount of exhaust gas that is reintroduced into the engine's combustion chamber, reducing harmful emissions such as nitrogen oxides.
The pintle-position sensor detects the position of the EGR valve's pintle, which is a crucial component in managing the flow of exhaust gases.
Potentiometers are widely used in various applications due to their ability to provide variable resistance based on the position of a sliding contact or wiper. In the case of an EGR pintle-position sensor, the potentiometer's wiper moves in accordance with the pintle's position, changing the resistance and generating a corresponding voltage signal. This signal is then sent to the engine control module (ECM), which uses this information to adjust the EGR valve's operation and maintain optimal engine performance.
While other types of sensors, such as Wheatstone bridge, piezoelectric, and rheostat sensors, are utilized in various applications, they are not typically used for EGR pintle-position sensing. Wheatstone bridge sensors are commonly used for measuring strain and pressure, piezoelectric sensors are used for detecting vibrations or dynamic forces, and rheostats are primarily used to control electrical current. Therefore, a potentiometer is the most suitable type of sensor for accurately detecting the position of the EGR valve's pintle.
Learn more about combustion chamber here:-
https://brainly.com/question/31830587
#SPJ11
A solar collector design consists of an inner tube enclosed concentrically in an outer tube that is transparent to solar radiation. The tubes are thin walled with inner and outer diameters of 0.10 and 0.15 m, respectively. The annular space between the tubes is completely enclosed and filled with air at atmospheric pressure. Under operating conditions for which the inner and outer tube surface temperatures are 70 and 30 C, respectively, what is the convective heat loss per meter of tube length across the air space?
The convective heat loss per meter of tube length across the air space in the given solar collector design is approximately 34.6 W/m.
To calculate the convective heat loss per meter of tube length across the air space in a solar collector design with an inner tube enclosed concentrically in an outer tube filled with air at atmospheric pressure, we can use the following steps:
Step 1: Calculate the temperature difference between the inner and outer tube surfaces:
ΔT = 70°C - 30°C = 40°C
Step 2: Calculate the average temperature of the air in the annular space:
T_avg = (70°C + 30°C) / 2 = 50°C
Step 3: Calculate the thermal conductivity of air at the average temperature:
k = 0.026 W/(m·K)
Step 4: Calculate the characteristic length of the annular space:
L = (0.15 m - 0.10 m) / 2 = 0.025 m
Step 5: Calculate the Rayleigh number:
Ra = (g β ΔT L^3) / (ν α)
where g is the acceleration due to gravity, β is the coefficient of thermal expansion, ν is the kinematic viscosity, and α is the thermal diffusivity of air. Using the values of these parameters at the average temperature, we get:
Ra = [tex](9.81 m/s^* 1/273 K^-1 * 40 K * 0.025 m^3) / (15.89 * 10^-6 m^2/s * 2.33 * 10^-5 m^2/s)[/tex] ≈ 275,000
Step 6: Calculate the Nusselt number using the following correlation for natural convection in an annulus:
[tex]Nu = 0.088 Ra^{(1/3)} (1 + (d_i / d_o))^{(1/4)[/tex]
where d_i and d_o are the inner and outer diameters of the tubes, respectively. Plugging in the given values, we get:
[tex]Nu = 0.088 * 275,000^{(1/3)} (1 + (0.10 m / 0.15 m))^{(1/4)[/tex] ≈ 33.3
Step 7: Calculate the convective heat transfer coefficient:
h = Nu x k / L = 33.3 x 0.026 W/(m·K) / 0.025 m ≈ 34.7 W/(m^2·K)
Step 8: Calculate the convective heat loss per meter of tube length:
[tex]q_{conv[/tex] = h x π x L x ΔT = 34.7 W/(m^2·K) x π x 0.025 m x 40°C ≈ 34.6 W/m
Therefore, the convective heat loss per meter of tube length across the air space in the given solar collector design is approximately 34.6 W/m.
Learn more about thermal conductivity :
https://brainly.com/question/14553214
#SPJ11
Assume ideal gas properties, consider a 500 mL cylinder that contains a mixture of heptane and air at 350K, and 1 atm.7H16 + 112→72 + 8H2The oxygen is at 10% excess.1.How many moles of oxygen, nitrogen and heptane are in the cylinder?
By using the ideal gas law and considering the composition of air, the excess oxygen, and the remaining volume in the cylinder, we can calculate the moles of each component.
How can we determine the number of moles of oxygen, nitrogen, and heptane in the cylinder?
To determine the number of moles of oxygen, nitrogen, and heptane in the cylinder, we need to consider the given conditions and use the ideal gas law.
First, we need to calculate the number of moles of air in the cylinder. Since air is composed of approximately 21% oxygen and 79% nitrogen by volume, we can calculate the moles of air using its molar volume at the given temperature and pressure.
Next, we determine the moles of oxygen by considering the 10% excess oxygen. We subtract the moles of air from the moles of oxygen to find the excess moles of oxygen.
Finally, we calculate the moles of heptane by assuming that the heptane occupies the remaining volume in the cylinder after accounting for the air and oxygen.
By applying the ideal gas law and the given volume, temperature, and pressure, we can determine the number of moles of each component in the cylinder.
Learn more about moles
brainly.com/question/30885025
#SPJ11
The program must do the following:Prompt the user for how many random sentences they want. Use a while or do/while loop to force the user to enter a number in the range 1-25 inclusive.Create arrays to store random articles, nouns, verbs, and prepositions. Use this data as an example, but create your own words for nouns and verbs:Articles: "the", "a", "one", "some", "any"Nouns: "person", "man", "woman", "dog", "cat", "city", "car", "bicycle"Verbs: "ran", "walked", "jumped", "skipped", "traveled", "drove"Prepositions: "to", "from", "over", "under", "on", "by", "for", "away", "towards", "around", "near"
Thus, to fulfill the requirements of this program, you will need to prompt the user for how many random sentences they want.
You will need to use a while or do/while loop to ensure that the user enters a number between 1-25 inclusive.
Once you have the user input, you will need to create arrays to store random articles, nouns, verbs, and prepositions.
You can use the following examples as a guide, but be sure to create your own words for nouns and verbs:
Articles: "the", "a", "one", "some", "any"
Nouns: "person", "man", "woman", "dog", "cat", "city", "car", "bicycle"
Verbs: "ran", "walked", "jumped", "skipped", "traveled", "drove"
Prepositions: "to", "from", "over", "under", "on", "by", "for", "away", "towards", "around", "near"
Using these arrays, you can generate random sentences by combining a random article, noun, verb, and preposition. You can repeat this process as many times as the user specified at the beginning of the program.
Remember to use proper syntax and formatting to ensure that the program runs smoothly and produces the desired output.
Know more about the do/while loop
https://brainly.com/question/26568485
#SPJ11
what is the relation between the number of transmit antennas and the number of receive antennas for spatial multiplexing to be possible. provide a mathematical argument for your answer.
The number of transmit antennas should be greater than or equal to the number of receive antennas for spatial multiplexing to be possible. This is because spatial multiplexing is a technique used in MIMO (multiple input multiple outputs) systems that utilizes multiple antennas at both the transmitter and receiver to increase the data rate and reliability of wireless communication.
The number of transmit antennas determines the number of independent data streams that can be transmitted simultaneously, while the number of receive antennas determines the number of independent data streams that can be received simultaneously. Therefore, if the number of transmit antennas is less than the number of receive antennas, there will be fewer independent data streams transmitted than received, which makes spatial multiplexing impossible.
Mathematically, the number of independent data streams that can be transmitted and received simultaneously is equal to the minimum of the number of transmit antennas and the number of receive antennas. This is known as the rank of the channel matrix, which is a measure of the number of independent dimensions of the MIMO channel. If the rank is less than the number of data streams, spatial multiplexing cannot be used, and the capacity of the channel is limited by the rank.
Therefore, to enable spatial multiplexing, the number of transmit antennas should be greater than or equal to the number of receive antennas, and the rank of the channel matrix should be equal to the number of independent data streams. This can be achieved by using advanced signal processing techniques, such as precoding and beamforming, to manipulate the channel matrix and increase its rank.
Learn more about MIMO (multiple input multiple outputs): https://brainly.com/question/31429289
#SPJ11
technician a says powertrain mounts hold the engine and transmission in proper position in the vehicle. technician b says a faulty powertrain mount cannot affect throttle linkage. who is correct?
Powertrain mounts are utilized in vehicles to keep the engine and transmission in the right place, therefore, the correct answer is technician A is correct, but technician B is incorrect.
Powertrain mounts, also known as engine mounts, are frequently created of metal and rubber and attach the engine and transmission to the vehicle's chassis. The mounts are linked to the chassis on one end and the engine or transmission on the other end. The engine mount holds the engine securely in place, while the transmission mount holds the transmission in place. As a result, technician A is correct on this issue.A faulty powertrain mount, on the other hand, can certainly influence the throttle linkage.
The throttle linkage is an essential component of the engine control system that governs how much fuel and air enter the engine. The throttle linkage can be moved by a faulty engine mount, which can cause it to bind or stick. When the throttle sticks, the engine speed can increase without the driver pressing on the accelerator pedal, which can be dangerous. As a result, technician B is incorrect about this problem.
Learn more about Powertrain mounts: https://brainly.com/question/12975348
#SPJ11
describe the main differences between defects and antipatterns
Defects and antipatterns are both types of problems in software development, but they differ in their nature and causes.
Defects are errors or bugs in the code that cause the software to behave in unintended ways, and they are usually caused by mistakes or oversights during the development process. Antipatterns, on the other hand, are recurring design problems or bad practices that lead to poor code quality and maintainability.
Defects, also known as bugs, are unintended errors in a software system's code or design that lead to undesirable outcomes. These can include incorrect calculations, crashes, or performance issues. Defects usually arise due to human error or oversights during development.
To know more about Software development visit:-
https://brainly.com/question/31060847
#SPJ11
Defects and antipatterns are both problematic aspects in software development as defects are specific flaws or errors in the code or system while antipatterns are recurring design or implementation issues.
What are the main differences between defects and antipatterns?Defects are individual faults that can manifest as incorrect behavior, crashes or vulnerabilities in software. They are typically caused by coding mistakes, logic errors or inadequate testing.
The antipatterns are broader patterns of design or development that are considered counterproductive or inefficient. They represent common pitfalls or bad practices that can lead to defects, suboptimal performance or difficulty in maintaining and extending the software.
Read more about software development
brainly.com/question/26135704
#SPJ4
Find the magnitude and sign of the power, in watts, absorbed by the circuit element in the box. 2A 322 a) -20 b) -8 c) 8 10V d) 12 17.61 For the circuit shown with v = 1V, the voltage across the 4-ohm resistor is a) 1/4 b) 1/2 c) 2/3 d) 2 422 812 822
The two questions given involve calculations related to circuits. The first question asks to find the magnitude and sign of the power absorbed by a circuit element in a box, while the second question asks to determine the voltage across a 4-ohm resistor in a circuit.
For the first question, we need to use the formula for power, which is P = IV, where P is power in watts, I is current in amperes, and V is voltage in volts. Since the current passing through the circuit element is 2A, and the voltage across it is 322V, we can calculate the power absorbed as follows:
P = IV
P = 2A x 322V
P = 644W
Since the voltage is positive and the current is flowing into the circuit element, the power absorbed is negative. Therefore, the correct answer is option (a) -20W.
For the second question, we can use Ohm's law, which states that V = IR, where V is voltage, I is current, and R is resistance. We are given that the voltage across the circuit is 1V, and we need to determine the voltage across the 4-ohm resistor. Let's call the current passing through the circuit I. Using Kirchhoff's voltage law, we can write:
1V = 4I + 8I + 2I
Simplifying the equation, we get:
1V = 14I
I = 1/14 A
Now we can use Ohm's law to find the voltage across the 4-ohm resistor:
V = IR
V = (1/14 A) x 4 ohm
V = 4/14 V
V = 2/7 V
Therefore, the correct answer is option (c) 2/3.
In summary, we have used the formulas for power and Ohm's law to solve the given questions related to circuits. It is important to have a good understanding of these concepts to analyze and design electrical circuits.
To learn more about circuits, visit:
https://brainly.com/question/12608491
#SPJ11