(a) The period of the pendulum on the moon would increase. (b) The period of the pendulum on the moon can be calculated using the formula [tex]T=2\pi\sqrt\dfrac{l}{g}[/tex] where T is the period, L is the length of the pendulum, and g is the acceleration due to gravity. In this case, the period of the pendulum on the moon is approximately 8.12 times greater than the period of the pendulum on the earth..
The formula of the period of a simple pendulum is given as:
[tex]T=2\pi\sqrt\dfrac{l}{g}[/tex]
Where T is the time period of the pendulum, l is the length of the pendulum, and g is the acceleration due to gravity
.From the above formula, we can see that the period of a pendulum is inversely proportional to the square root of acceleration due to gravity.
Therefore, the period of the pendulum will be increased when the acceleration due to gravity decreased from earth to moon. The period of the pendulum on the moon would increase.
(b) The acceleration due to gravity on the moon is 0.17g. Therefore, the period of the pendulum on the moon can be determined by using the formula of the period of a simple pendulum.
[tex]T=2\pi\sqrt{\dfrac{l}{g}}\\T=2\pi\sqrt{\dfrac{l}{0.17g}[/tex]
Now, substituting the given values in the above equation:
[tex]T=2\pi\sqrt{\dfrac{l}{(0.17\times9.81)}}\\T=2\pi\sqrt{1.67l}\\T=2\pi\times1.29\sqrt{l}\\T=8.12\sqrt{l}[/tex]
Therefore, the period of the pendulum on the moon is 8.12 times greater than the period of the pendulum on the earth.
To know more about time period of pendulum, click on the below link:
https://brainly.com/question/29074269
#SPJ11
upslope fog hugging the mountain surface occurs when: question 12 options: a. air warms because of decreasing atmospheric pressure
b. eventually air cools to the dew-point temperature air warms because of decreasing atmospheric pressure
c. eventually air warms to the dew-point temperature air cools because of increasing atmospheric pressure
d. eventually air cools to the dew-point temperature air cools because of decreasing atmospheric pressure
e. eventually air cools to the dew-point temperature
A decrease in atmospheric pressure eventually causes air to cool to the dew-point temperature.
How does surface-hugging upslope fog on mountains occur?Fog on an upward slope forms adiabatically. The process through which ascending air cools and sinking air warms is known as adiabatic cooling. The air rises and cools as wet breezes blow in the direction of a mountain. The dew point temperature is reached as a result of the rising air cooling.
Upslope fog: what is it?This type happens when air is lifted by sloping terrain and is adiabatically cooled to its dew point and saturation. Depending on the observer's frame of reference, upslope fog can be seen as either a stratus cloud or a fog.
To know more about temperature visit:-
https://brainly.com/question/4160783
#SPJ1
when you look at a spiral that appears to move inward for about a minute, and then look at a stationary object, the object will briefly appear to ......
When you look at a spiral that appears to move inward for about a minute, and then look at a stationary object, the object will briefly appear to move outwards. This phenomenon is known as the motion aftereffect (MAE).
After staring at the spiral for about a minute, your brain becomes accustomed to the constant motion of the spiral. When you look away from the spiral and fix your gaze on a stationary object, your brain continues to perceive motion in the opposite direction (outwards).
This is why the stationary object appears to move outwards for a brief period. The motion aftereffect is an example of the adaptation process that takes place in the visual system. It is a perceptual illusion that occurs when the brain is exposed to a particular type of visual stimulus for a prolonged period of time.
Hence, when you look at a spiral that appears to move inward for about a minute, and then look at a stationary object, the object will briefly appear to move outwards.
To know more about Motion Aftereffect, refer here:
https://brainly.com/question/15556402#
#SPJ11
Use the radius-luminosity-temperature relation to calculate the radius of a red supergiant with temperature 3000 K and total luminosity 60000 times that of the Sun. (Sec. 17.3 in the textbook)Express your answer using two significant figures.R= ___________ AU
A red supergiant with a temperature of 3000 K and a total luminosity of 60000 times that of the Sun, using the radius-luminosity-temperature relationship the radius is 700 AU (to two significant figures).
The radius-luminosity-temperature relation can be used to calculate the radius of a red supergiant. Given a temperature of 3000 K and a total luminosity of 60000 times that of the Sun, the radius can be calculated as follows:
R = (L/Lsun)[tex]^{\frac{1}{2} }[/tex]* (Teff/Teff,sun)⁻²
where R is the radius of the star, L is the luminosity, Teff is the effective temperature, and Lsun and Teff, sun are the luminosity and effective temperature of the Sun, respectively.
Substituting the given values, we get:
R = (60000)[tex]^{\frac{1}{2} }[/tex] * (3000/5777)⁻²
R = 4657.88 AU
Therefore, the radius of the red supergiant is approximately 4700 AU (two significant figures).
Learn more about radius-luminosity-temperature at https://brainly.com/question/14291232
#SPJ11
the regular satellites of the giant planets formed via the process of
The regular satellites of the giant planets formed via the process of accretion from a circumplanetary disk.
The giant planets in our solar system, such as Jupiter, Saturn, Uranus, and Neptune, are surrounded by a system of moons, which are divided into two main categories: regular and irregular. The regular satellites are large, spherical, and have nearly circular orbits around their host planets. They are believed to have formed from a circumplanetary disk of gas and dust that surrounded the planet during its formation. The gravitational forces of the planet caused the material in the disk to accrete into small bodies, which eventually coalesced into the regular satellites we see today.
To know more about satellites, here
brainly.com/question/21675499
#SPJ4
the end result of a theory that is not verified is
Unproven theories ultimately cannot be regarded as scientific facts or principles and are not generally recognised by the scientific community.
A well-supported explanation of a natural occurrence in science that has passed rigorous examination and is backed by empirical data is referred to as a theory. A hypothesis, however, cannot be regarded as a scientific fact or principle if it is not backed up by empirical data or if it has not undergone extensive testing and verification. The scientific community frequently rejects unproven notions with scant empirical backing and may even label them as pseudoscientific or non-scientific. This is so that scientific theories and findings may be evaluated and verified frequently. Science does this by using evidence-based reasoning and critical thinking. Unproven theories are therefore eventually not regarded as being a part of the corpus of scientific knowledge.
learn more about theories here:
https://brainly.com/question/1759635
#SPJ4
The control surface of an aircraft is supported by a thrust bearing at point C and isactuated by a bar connected to point A. The 1 kN force acts in the negative z direction,and the line connecting points A and B is parallel to the z axis. Determine the value offorce F needed for equilibrium and all support reactions.
It takes 1.414 kN of force F to achieve equilibrium and all supporting processes.
What is Force?An external force is an agent that has the power to alter the resting or moving condition of a body. It has a trajectory and a magnitude. The application of force is the place at which force is applied, and the direction in which the force is applied is known as the direction of the force.
The force applied in the negative z direction, A and B are connected through the bar and C is the thrust bearing. Determine the value of force F needed for equilibrium and all support reactions.
Steps to find the value of force F required for equilibrium and all support reactions:
Firstly, the control surface of an aircraft is supported by a thrust bearing at point C and is actuated by a bar connected to point A. The 1 kN force acts in the negative z direction and the line connecting points A and B is parallel to the z-axis. We have to determine the value of the force F required for equilibrium and all support reactions.
There are three supports; at A, B, and C. Let's consider that RAB, RBC, and RCB are reactions at A, B, and C, respectively. There are two directions, one is positive and the other is negative.
In the next step, the upward direction is positive and the downward direction is negative. Sum of forces in the x-direction:F cosθ = 0 ⇒ F = 0. Sum of forces in the y-direction:F sinθ - 1000N = 0 ⇒ F sinθ = 1000NCosθ = 1 (as cos0° = 1)⇒ F = 1000N/sinθ⇒ F = 1000N/sin(90° - θ)⇒ F = 1000N/cosθ. For equilibrium, sum of moments about point C (Taking clockwise moment as negative):FC x 0.5 - RAB x 0.5 - RCB x 1 = 0RAB + RCB = FC.
Thus, the value of force F needed for equilibrium and all support reactions is 1.414 kN.
Learn more about force on:
https://brainly.com/question/25256383
#SPJ11
two long parallel wires placed side-by-side on a horizontal table carry identical current straight toward you. from your point of view, the magnetic field at the point exactly between the two wires select one: a. points down. b. points toward you. c. is zero. d. points away from you.
The magnetic field at the point exactly between the two wires will point away from your point of view is zero. The correct option is C.
What is the magnetic field?The two currents in the wires create a parallel magnetic field, which is oriented so that the same pole is facing each other (in this case, the north pole). This causes the field lines to repel away from each other, creating a magnetic field that points away from the midpoint between the wires.
The magnetic field at the point exactly between the two wires is zero. Two parallel long wires that carry identical currents straight towards us are placed side by side on a horizontal table.
As a result, the net magnetic field is zero.
Therefore, the correct option is C.
Read more about magnetic field here:
https://brainly.com/question/14411049
#SPJ11
19. Which statement correctly describes a short circuit?
O A. Having a part with very low resistance keeps the circuit cooler, preventing
damage caused by overheating.
O B. Almost no current flows through a part of a circuit that has very low resistance
because it goes through the load.
OC. Almost all the current flows through a part of a parallel circuit with very low
resistance, instead of through the rest of the circuit.
O D. Having a part with very low resistance keeps circuit breakers and fuses from
opening the circuit
oc, it's the closest definition to a short circuit
Answer: almost all the current flows through a part of a parallel circuit, with very low resistance, instead of through the rest of the circuit.
Explanation:
suppose your planet at 1 meter from the basketball represents a distance of 4 x 107 km (-0.3 al) from the star. the next closest star to the sun is 4 x 1013 km away. how far away from the model star/planet would you have to be for the distances in the system to be to scale? express your answer in meters and kilometers.
Answer: The model star/planet would have to be 1,000 km away from the next closest star.
Explanation:
We need to find out the distance required for the distances in the system to be in scale.
Let's use the proportion to solve the problem:
1 m/4 × 10⁷ km = x/4 × 10¹³ km
Where x is the distance required for the distances in the system to be in scale.
Cross-multiply: 4 × 10¹³ km × 1 m = 4 × 10⁷ km × x
Simplify: 4 × 10¹³ m = 4 × 10⁷ x
Divide both sides by 4 × 10⁷ :1 × 10⁶ = x
Therefore, the distance required for the distances in the system to be in scale is 1 × 10⁶ m or 1,000 km.
So the model star/planet would have to be 1,000 km away from the next closest star.
Learn more about distance here
https://brainly.com/question/26550516
#SPJ11
which of the following capacitors, each of which has plates of area a, would store the most charge on the top plate for a given potential difference v ? A. 2 vacuum with d
B. 2 plates with glass with d
C. 2 vacuum with d/2
D. 2 plates with air d/2
E. 2 plates with glass d/2
In this case, the plates of the d/2 have an area a and a separation of d, d/2, or 2d. The correct option D have separation of d/2 is the one that can store the maximum charge on its top plate.
Capacitance is the capability of an object to store an electrical charge. Capacitance is calculated as the ratio of the charge stored to the potential difference between the plates of the capacitor.Capacitance = Charge/ Potential differenceThe equation shows that the charge that can be stored on a capacitor plate increases when the capacitance of the capacitor is high.The capacitance of a capacitor is proportional to the plate area and inversely proportional to the separation between the plates. It implies that if the plate area of a capacitor increases, the capacitance increases and if the separation between the plates decreases, the capacitance increases.Considering the above information, option D has plates with air of separation d/2. Since the air between the plates has a lower dielectric constant, the capacitance of the capacitor decreases. So, the charge stored on the capacitor will increase as the capacitance decreases. Therefore, the capacitor with the separation of d/2 can store the maximum charge on the top plate for a given potential difference v. Hence, the correct answer is option D.Learn more about capacitors: https://brainly.com/question/13578522
#SPJ11
which researcher discovered the principles of classical conditioning?
The principles of classical conditioning were first discovered by Ivan Pavlov, a Russian physiologist, in the late 19th century.
Pavlov was conducting research on digestion in dogs when he observed that the dogs began to salivate at the sound of a bell that was regularly associated with the presentation of food.
This led him to develop the concept of conditioned reflexes, where a neutral stimulus (like the sound of the bell) could become associated with a meaningful stimulus (like the presentation of food) and elicit a response. Pavlov's research on classical conditioning laid the foundation for the study of learning and behavior, and his work has had a profound impact on psychology and other fields of study.
To learn more about reflexes refer to:
brainly.com/question/29727145
#SPJ4
calculate the work done by gravity on the watermelon during its displacement from the roof to the ground
The work done by gravity on the watermelon during its displacement from the roof to the ground is 196 J.
The work done by gravity on the watermelon during its displacement from the roof to the ground can be calculated using the formula W = mgh, where W is the work done, m is the mass of the watermelon, g is the acceleration due to gravity and h is the height of the displacement.What is Work Done?Work done can be defined as the energy transferred when a force is applied to an object to move it over a certain distance. It is a scalar quantity and is measured in joules (J). The mass of the watermelon is not given in the question, so let us assume that the mass of the watermelon is 2 kg. The acceleration due to gravity, g is 9.8 m/s2, and the height of the displacement is not given in the question, so let us assume that the height of the displacement is 10 meters. Therefore, the work done by gravity on the watermelon during its displacement from the roof to the ground can be calculated as follows: W = mgh= (2 kg) (9.8 m/s2) (10 m)= 196J
Therefore, the work done by gravity on the watermelon during its displacement from the roof to the ground is 196 J.
Learn more about work done at brainly.com/question/13662169
#SPJ4
now consider the case of impending tipping. where do the normal force and friction force act in this case? a. at the midpoint of the bottom edge of the block. b. at the point directly below the center of gravity of the block. c. at the edge of the block closest to the top of the ramp. d. at the edge of the block closest to the bottom of the ramp. e. at an unknown point along the bottom edge of the block.
The normal force and friction force act at the point directly below the center of gravity of the block in the case of impending tipping.
Impending tipping occurs when the force of gravity acting on an object is unbalanced, causing it to start to tip over or become unstable.
When a solid object is about to tip over, the net torque about its center of gravity should be zero, or else it will fall.
In the case of impending tipping, the normal force and friction force act at the point directly below the center of gravity of the block.
When an object is about to tip over, the normal force (or the weight) acting on the center of mass should be equal to the maximum possible friction force at the base of the object.
Normally, a force is applied to the object that exceeds this friction force, causing the object to tip over.
When an object is about to tip over, the normal force (or the weight) acting on the center of mass should be equal to the maximum possible friction force at the base of the object.
To know more about normal force: https://brainly.com/question/28788588
#SPJ11
which compound in each set is aromatic? part a cyclopropene is a ring with three vertices and a double bond between the first and the second (clockwise) vertices. a cyclopropenyl cation is a ring with three vertices, a double bond between the first and the second (clockwise) vertices, and a positive charge at the third vertex. a cyclopropenyl anion is a ring with three vertices and a double bond between the first and the second (clockwise) vertices. there is a negative charge and a lone pair at the third vertex. cyclopropene is a ring with three vertices and a double bond between the first and the second (clockwise) vertices. a cyclopropenyl cation is a ring with three vertices, a double bond between the first and the second (clockwise) vertices, and a positive charge at the third vertex. a cyclopropenyl anion is a ring with three vertices and a double bond between the first and the second (clockwise) vertices. there is a negative charge and a lone pair at the third vertex. cyclopropene cyclopropenyl cation cyclopropenyl anion
Cyclopropene is a ring with three vertices and a double bond between the first and the second (clockwise) vertices.
A cyclopropenyl cation is a ring with three vertices, a double bond between the first and the second (clockwise) vertices, and a positive charge at the third vertex. A cyclopropenyl anion is a ring with three vertices and a double bond between the first and the second (clockwise) vertices. There is a negative charge and a lone pair at the third vertex. Cyclopropene is the only compound in the set that is aromatic.
Learn more about compound at:
https://brainly.com/question/18882451
#SPJ11
the diagram below shows four cannons firing shells with different masses at different angles of elevation. the horizontal component of the shell's velocity is the same in all four cases. in which case will the shell have the greatest range if air resistance is neglected? (a) cannon a (b) cannon b only (c) cannon c only (d) cannon d
The diagram below shows four cannons firing shells with different masses at different angles of elevation. the horizontal component of the shell's velocity is the same in all four cases. The case will the shell have the greatest range if air resistance is neglected is (a) cannon a
The cannon which would have the maximum range if air resistance is neglected is given by the expression R = (V²/g)sin(2θ). The horizontal component of velocity is the same for all four shells, Vx = Vcosθ. Where R is the range, V is the velocity, g is the gravitational acceleration, θ is the angle of projection, and Vx is the horizontal component of the velocity. The diagram below shows four cannons firing shells with different masses at different angles of elevation.
For the maximum range, we need to take the angle of projection to be 45°. The mass of the shell is not a consideration since it doesn't affect the time of flight or the range of the shell.Therefore, the maximum range is given by the highest value of V²sin(2θ)/g. As sin(90) = 1, sin(0) = 0, sin(30) = 1/2, sin(45) = √2/2, sin(60) = √3/2, sin(70) = 0.94, the maximum value of sin(2θ) is obtained when θ = 45°.For all four cannons, the horizontal component of velocity, Vx = Vcosθ, is the same. Therefore, the maximum range is obtained for Cannon A when air resistance is neglected. Therefore, the correct answer is (a) Cannon A.
Learn more about maximum range at:
https://brainly.com/question/321411
#SPJ11
Q9: A bungee jumper falls with a total of 7.8kJ of kinetic energy. If the bungee jumper's total mass is 50kg, at what speed do they fall?
The bungee jumper falls at a speed of approximately 17.67 meters per second.
What is the bungee jumper fall speed?Kinetic energy is simply a form of energy a particle or object possesses due to its motion.
It is expressed as;
K = (1/2)mv²
Where m is mass of the object and v is its velocity.
We know that the kinetic energy of the bungee jumper is 7.8 kJ and their mass is 50 kg.
Substituting these values into the equation gives:
K = (1/2)mv²
7.8 kJ = (1/2) × 50 kg × v²
Convert from kiloJoule to Joule
7.8 kJ = (7.8 × 1000 ) = 7800J
Simplifying:
7800J = (1/2) × 50 kg × v²
7800 kgm²/s² = (1/2) × 50 kg × v²
7800 kgm²/s² = 25 kg × v²
v² = 7800 kgm²/s² ÷ 25kg
v² = 312 m²/s²
Taking the square root of both sides:
v = √( 312 m²/s² )
v = 17.67 m/s
Therefore, the fall speed is 17.67 m/s.
Learn more about kinetic energy here: brainly.com/question/12669551
#SPJ1
Consult Multiple-Concept Example 10 in preparation for this problem. Traveling at a speed of 16.1 m/s, the driver of an automobile suddenly locks the wheels by slamming on the brakes. The coefficient of kinetic friction between the tires and the road is 0.720. What is the speed of the automobile after 1.30s have elapsed? Ignore the effects of air resistance.
The speed of the automobile after 1.30 seconds have elapsed is 15.164 m/s.
Given the following data,
we will have to calculate the velocity of the car after 1.30 seconds:
Initial velocity, u = 16.1 m/s
Final velocity, v =?
Time elapsed, t = 1.30s
Coefficient of kinetic friction, μk = 0.720
We will apply the law of motion, i.e., v = u - μkt
Where, v is the final velocity of the car after 1.30 seconds,
u is the initial velocity of the car,
μk is the coefficient of kinetic friction,
t is the time elapsed after 1.30 seconds
Given values,
u = 16.1 m/sμk = 0.720t = 1.30s
Substituting the given values in the equation,
we get v = 16.1 m/s - (0.720 x 1.30s)
v = 16.1 m/s - 0.936v = 15.164 m/s
Therefore, the speed of the automobile after 1.30 seconds have elapsed is 15.164 m/s.
To know more about Speed: https://brainly.com/question/5248528
#SPJ11
a solenoid with 400 turns has a radius of 0.040 m and is 40 cm long. if this solenoid carries a current of 12 a, what is the magnitude of the magnetic field at the center of the solenoid? select one: a. 15 mt b. 9.0 mt c. 16 mt d. 4.9 mt e. 6.0 mt
The magnetic field at the center of the solenoid is 15 mT
We are required to calculate the magnetic field at the center of the solenoid.
Number of turns in solenoid, N = 400
Radius of solenoid, r = 0.040 m
Length of solenoid, l = 40 cm = 0.4 m
Current passing through solenoid, I = 12 A
Magnetic field at the center of the solenoid can be calculated using the following formula: B = μ_0 n I
μ_0 is the magnetic permeability of free space which is equal to 4π × 10⁻⁷ Tm/A.
N is the number of turns per unit length of the solenoid.
n = N/l Where N is the total number of turns in the solenoid and l is the length of the solenoid.
Substituting the given values in the above formula: B = (4π × 10⁻⁷ Tm/A) × (N/l) × I
We know that l = 0.4 m and N = 400Therefore, n = N/l = 400/0.4 = 1000 turns/m
Now, substituting the values of N, l, n and I in the above formula we get:
B = (4π × 10⁻⁷ Tm/A) × (1000 turns/m) × (12 A) = 0.015 T = 15 mT
To know more about magnetic field, refer here:
https://brainly.com/question/23096032#
SPJ11#
A typical value for the dielectric constant of rubber is a minimum of 2. Give one reason why your experimental value was less than two!
What are the dependent and independent variables in thid experiment?
The independent variable in this experiment is the dielectric constant of rubber, and the dependent variable is the measured value. The typical value for the dielectric constant of rubber is a minimum of 2, but your experimental value could have been lower than two.
The dependent and independent variables in this experiment are not specified. Therefore, it is impossible to answer the question accurately. A typical value for the dielectric constant of rubber is a minimum of 2.
The dielectric constant is defined as the ratio of the electric flux density produced in a substance to that produced in a vacuum by the same electric field.
The dielectric constant is a measure of a substance's ability to store charge in an electric field. The dielectric constant of a substance indicates how easily it can be polarized in response to an applied electric field.
It varies with temperature, frequency, and pressure, among other factors.
Learn more about dielectric constants here:
https://brainly.com/question/13265076
#SPJ11
A circular coil lies flat on a horizontal table. A bar magnet is held above its centre with its north pole pointing down, and released. As it approaches the coil, the falling magnet induces (when viewed from above) ...no current in the coil.a clockwise current in the coil.a counter clockwise current in the coil.a current whose direction cannot be determined from the information provided
As the released bar magnet approaches the coil, the falling magnet induces a counter clockwise current in the coil.The direction of the induced current in the coil is counter-clockwise.
A magnetic field exists when there is a change in magnetic flux. The change in magnetic flux is due to the relative motion between the bar magnet and the coil. The bar magnet produces a magnetic field as it falls towards the coil. The change in magnetic flux is proportional to the rate of change of the magnetic field.
Faraday's law of electromagnetic induction states that when a magnetic field that varies with time is passed through a coil, an electromotive force (EMF) is induced in it. When the magnet is dropped through the coil, the magnetic field through the coil varies, inducing an EMF in it. The EMF causes an induced current to flow through the coil. The direction of the induced current is counter-clockwise.
More on electromagnets: https://brainly.com/question/14856796
#SPJ11
While analyzing smoke detector designs that rely on the photoelectric effect, you are evaluating surfaces made from each of the materials listed in (Figure 1). One particular application uses ultraviolet light with wavelength 273 nm
Photodetectors that rely on the external photoelectric effect are known as photoemissive detectors (sometimes spelled photoelectric detectors).
A photocathode of some kind is present in such a device, where incident light is partially absorbed to produce photoelectrons, which are released into free space.
The light reflected off of particles by a light beam inside the sensor chamber is used by smoke detectors to detect smoke. When there are no particles in the sensing chamber, the beam's light does not hit the light detector, signaling that everything is in order.
Ionization smoke alarms detect smoke from rapidly blazing fires, while photoelectric smoke detectors are best for detecting smoke from smoldering fires.
To know about detector
https://brainly.com/question/28592245
#SPJ4
When an arrow is shot from a bow, it has kinetic energy in it. From where does it get its kinetic energy?
An arrow shot from a bow gets its kinetic energy from the potential energy stored in the bowstring and limbs. When the bowstring is pulled back, it stores energy in the limbs as elastic potential energy.
What is kinetic energy?
Kinetic energy is defined as the energy an object has due to its motion. When an arrow is shot from a bow, it is set in motion and therefore has kinetic energy. The kinetic energy of the arrow depends on its mass and speed. The heavier the arrow, the more kinetic energy it has, and the faster the arrow, the more kinetic energy it has.
The energy stored in the bow is transferred to the arrow when the string is released and the limbs snap back to their original position. This causes the arrow to be propelled forward with a significant amount of kinetic energy.
To know more about potential energy:
https://brainly.com/question/9547709
#SPJ11
A car travelling at 22.4 m/s skids to a stop in 2.55s. Determine the skidding distance of the car (assume uniform acceleration).
Answer:
Approximately [tex]28.6\; {\rm m}[/tex].
Explanation:
Let [tex]u[/tex] denote the initial velocity of the vehicle, and let [tex]v[/tex] denote the velocity of the vehicle after skidding. It is given that the initial velocity was [tex]u = 22.4\; {\rm m\cdot s^{-1}}[/tex]. Since the vehicle skidded to a stop, [tex]v = 0\; {\rm m\cdot s^{-1}}[/tex].
Let [tex]t[/tex] denote the duration of the skid. It is given that [tex]t = 2.55\; {\rm s}[/tex].
Under the assumption that acceleration is constant, SUVAT equations will apply.
Specifically, the SUVAT equation [tex]x &= (1/2)\, (u + v)\, t[/tex] will be satisfied. In this equation, the displacement of the vehicle is equal to average velocity times duration. This equation allows the displacement [tex]x[/tex] to be found from [tex]u[/tex], [tex]v[/tex], and [tex]t[/tex] without knowing the exact value of acceleration:
[tex]\begin{aligned}x &= \left(\frac{u + v}{2}\right)\, t \\ &= \left(\frac{22.4 + 0}{2}\; {\rm m\cdot s^{-1}}\right)\; (2.55\; {\rm s}) \\ &\approx 28.6\; {\rm m}\end{aligned}[/tex].
explain why hydrogen is not a dominant component of the atmospheres of the terrestrial planets, even though it is the most common element in the universe and in the solar system.
Hydrogen is not a dominant component of the atmospheres of the terrestrial planets, even though it is the most common element in the universe and solar system because it is a volatile and low molecular weight element.
What is Hydrogen?Hydrogen element is not a dominant component of the atmospheres of the terrestrial planets, even though it is one of the most common element in the universe and in the solar system as well because the planets were formed through the accretion.
Accretion is the process by which the small particles combine into progressively larger bodies which become planets. As a result of this, the process left behind the lighter gas elements such as hydrogen and helium. The gas molecules of hydrogen atom are lighter than the rest of the chemical elements, therefore the gravity of the terrestrial planets is not sufficient to hold them. As a result, hydrogen escapes from the planet's atmosphere, leaving behind the heavier elements like carbon dioxide, nitrogen, and oxygen in their atmospheres.
Therefore, although hydrogen is the most common element in the universe and in the solar system, it is not a major constituent of the terrestrial planets.
Learn more about Hydrogen atom here:
https://brainly.com/question/8806577
#SPJ11
A cylindrical pulley with a mass of 7.7 kg, radius of 0.532 m and moment of inertia 1/2 M r^2 is used to lower a bucket with a mass of 2.4 kg into a well. The bucket starts from rest and falls for 4.5 s. a) What is the linear acceleration of the falling bucket? The acceleration of gravity is 9.8 m/s^2. Answer in units of m/s^2. b) How far does it drop? Answer in units of m. c) Find the angular acceleration of the cylinder. Answer in units of rad/s22.
The linear acceleration of the falling bucket can be calculated using the formula.
a = g - (T/M)
where g is the acceleration of gravity (9.8 m/s²), T is the torque exerted by the pulley (T = Iα, where I is the moment of inertia, and α is the angular acceleration), and M is the mass of the bucket. We can calculate the torque of the pulley by substituting the given values:
T = (1/2 M r²) * (α)
T = (1/2) * (7.7 kg) * (0.532 m)² * (α)
T = 2.01 (kg m²) * (α).
Therefore,
a = 9.8 m/s² - (2.01 (kg m^2) * (α) /2.4 kg)
a = 9.58 m/s²
The distance traveled by the bucket can be calculated using the formula
d = (1/2) * a * t²
where a is the acceleration of the bucket (9.58 m/s²) and t is the time it takes to fall (4.5 s).
Therefore,
d = (1/2) * (9.58 m/s²) * (4.5 s)²
d = 98.2 m
The angular acceleration of the cylinder can be calculated using the formula
α = T/I
where T is the torque exerted by the pulley (2.01 (kg m²) * (α)) and I is the moment of inertia (1/2 M r²).
Therefore,
α = 2.01 (kg m²) * (α) / (1/2) * (7.7 kg) * (0.532 m)²
α = 10.3 rad/s²
Learn more about angular acceleration at https://brainly.com/question/13014974
#SPJ11
A__ is a measure of the electric power an appliance uses
An appliance's use of electricity is measured in watt (W). It displays the rate at which an electrical device uses energy while it is in operation. The power needed to generate one joule of energy per second is equal to one watt.
WattAn electrical device uses energy from the electrical power source that powers it when it is in use. Watts (W), a unit of power, is used to assess the rate of energy consumption. The pace at which one joule of energy is used up per second is equal to one watt.A 60-watt light bulb, for instance, means that when it is turned on, it uses energy at a rate of 60 joules per second. Similarly to this, when a fan with a 100-watt rating is switched on, it uses 100 joules of energy each second.An appliance's wattage can be found on its label or in its user manual.learn more about watt here
https://brainly.com/question/1446143
#SPJ1
how many types of classifications are there for a lunar eclipse?
There are three types of lunar eclipses: total, partial, and penumbral.
During a total lunar eclipse, the moon is completely shadowed by the Earth, resulting in a reddish-brown color. In a partial lunar eclipse, only a portion of the moon is shadowed, while in a penumbral lunar eclipse, the moon passes through the Earth's outer shadow, resulting in a subtle darkening of the moon's surface. These classifications are based on the degree to which the moon passes through the Earth's shadow during the eclipse.
To know more about lunar eclipse, here
brainly.com/question/29775053
#SPJ4
all of the wavelengths of visible light combine to form
All the wavelengths of visible light combine to form white light.
What is visible light?
Visible light is made up of different wavelengths of electromagnetic radiation that range in color from violet (shortest wavelength) to red (longest wavelength). When all of the wavelengths of visible light are combined, they form white light.
This can be observed in various phenomena, such as the splitting of white light into its component colors when passing through a prism, or when white light is shone onto a surface and reflects back as white.
What is an electromagnetic radiation?
Electromagnetic radiation is a form of energy that travels through space as a wave, without the need for a medium to propagate. It is made up of electric and magnetic fields that oscillate perpendicular to each other and to the direction of the wave's travel.
To know more about electromagnetic radiation, visit:
https://brainly.com/question/10759891
#SPJ1
Complete question is: All the wavelengths of visible light combine to form white light.
a piston cylinder containing air has an area of 0.011 m2 and a piston with a mass of 20.4 kg. if the atmospheric pressure is measured to be 102.3 kpa, what is the gauge pressure of the air inside the piston cylinder? the absolute pressure?
The gauge pressure of the air inside the piston cylinder is 21.849 kPa if the atmospheric pressure is measured to be 102.3 kpa .
What is gauge pressure ?The pressure relative to atmospheric pressure is known as gauge pressure. Gauge pressure is positive for pressures greater than atmospheric pressure and negative for pressures less than atmospheric pressure. In fact, atmospheric pressure increases the pressure in any fluid that is not contained in a rigid container. This occurs as a result of Pascal's principle.
Absolute pressure on piston = atmospheric pressure + pressure on piston
solving , 102.3 kPa
to know more about gauge pressure , visit ;
brainly.com/question/29341536
#SPJ1
The gauge pressure of the piston cylinder will be 17889.5 KPa and the absolute pressure of the piston cylinder will be 17991.8 KPa.
What is the gauge pressure?The gauge pressure inside the piston cylinder is calculated by subtracting the atmospheric pressure from the total pressure inside the cylinder. Therefore, the gauge pressure of the air inside the piston cylinder is calculated as follows:
Pgauge = Ptotal - Patm
Pgauge = F/A - Patm
Pgauge = (20.4kg × 9.8m/s²) / 0.011m² - 102.3 kPa
Pgauge = 17991.8 kPa - 102.3 kPa
Pgauge = 17889.5 kPa
The absolute pressure inside the piston cylinder is the sum of the atmospheric pressure and the gauge pressure. Therefore, the absolute pressure of the air inside the piston cylinder is calculated as follows:
Pabsolute = Pgauge + Patm
Pabsolute = 17889.5 kPa + 102.3 kPa
Pabsolute = 17991.8 kPa
Learn more about Pressure here:
https://brainly.com/question/29341536
#SPJ11
Without doing a calculation, predict which of these compounds has the greatest molar solubility in water . A) AgBr (Ksp = 5.0x10-13)
B) Agl (Ksp = 8.3x10-17)
C) AgCl (Ksp = 1.8x10-10)
Without doing a calculation, the compound that has the greatest molar solubility in water among the given compounds is AgCl.
The reason for this is because it has the largest Ksp value among the given options. Ksp, or the solubility product constant, is the equilibrium constant for the dissolution of a sparingly soluble compound in a solution. It represents the maximum amount of solute that may be dissolved in a solvent at equilibrium under given conditions.AgBr, AgI, and AgCl are all sparingly soluble in water.
They all have small solubility product constants, indicating that they dissolve very little in water at equilibrium. AgCl has the greatest molar solubility among the three options, according to the given Ksp values. Its solubility product constant is 1.8 x 10-10, which is much greater than those of AgBr and AgI. Therefore, AgCl is the compound with the greatest molar solubility in water without any calculation.In summary, among the given options, AgCl has the greatest molar solubility in water without any calculation.
More on molar solubility: https://brainly.com/question/7141822
#SPJ11